background image

 

  

  

www.iCeeO2.com

                                 

6  

 

 iCeeO2-500P_US_004English.docx

 

 

 

Function  Directions 
ALARM 

When ALARM is set ON, an audible alarm will resound if the CO

2

 level 

exceeds varying levels (depending on border lever set) . Once ALARM is 
selected (by pressing ENTER), use either UP or DOWN to toggle the 
selection from ON to OFF or vice versa. Press ENTER one more time to 
confirm. A regular bell icon will be displayed if alarm is on; a silenced 
bell icon will appear on the screen if the alarm is set to be off. 

TIME 

This function allows the user  to adjust the real-time, once TIME is 
selected, use UP and DOWN   to adjust the current date and time, Press 

ENTER  to comfirm.  

 
 
LOG 

This feature allows the user to see historical data recorded in the log at 
any point that is displayable on the chart. First make sure the desired 
Zoom Level is selected before enabling this function. Then once LOG is 
enabled, use UP and DOWN toggle between the time divisions  to see 
all parameters’ measurements for each division. Press ENTER once more 
to exit this mode. 

 
 
CALI 

Use this function to calibrate your device with outside atmospheric CO

level ~ 400ppm. Select this mode, hold ENTER for 3 seconds until a beep 
and the chart will read “Calibrating”, then place the device outside for 
20min. To escape, press MENU. Make sure the device is far from a source 
of CO2, not in direct sunlight, and not exposed to water. 

 
ALTI 

This feature provides an altitude correction to the CO

2

 level for increased 

accuracy. Select this feature, then use UP and DOWN to input the 
current altitude (look it up if unknown) in meters. Press ENTER once 
altitude is correct. 

 
ºC/ºF 

Use this feature to toggle between Celsius and Fahrenheit for the 
temperature display. First use UP and DOWN, then ENTER when the 
desired one is selected. 

 
 
ADV 

This function toggles between 3 things when selected: changing the 
alarm and lights to suit levels For Low border, or For Hi border, or 
Restore factory setting. 
Restore factory setting will reset the device to factory settings and erase 
all stored data in the chart. To use any of these modes, hold ENTER for 3 
seconds until an audible beep. 

(Return) 

Exits the main menu. No options will be displayed on the green bar. A 
different audible beep be heard in this option.  

 

 

 

 

 

 

 

 

Summary of Contents for 500P









Reviews: