Ice TIPPIN' BLOKS Owner'S And Service Manual Download Page 13 | Manualshive

Page: 13 / 18

background image

13

SERVICE

COMPUTER AND I/O CONTROL REPLACEMENT

The computer is located on the back door itself. Two chains provides support to the back door
when opened. Do not remove these chains for any reason. The computer is held on to the back
door by two straps. Pushing the sides of the buckle will release the straps. Be sure that the straps
are tight when finished.

«
...
11
12
13
14
15
...
»

Summary of Contents for TIPPIN' BLOKS



















Reviews:

No comments

Related manuals for TIPPIN' BLOKS

Brand: ASTRO Pages: 50

Brand: SEGA ENTERPRISES Pages: 84

Brand: NAMCO Pages: 29

Brand: LAI Games Pages: 82

Fruit Ninja FX 2

Brand: Adrenaline Amusements Pages: 33

Brand: Bally Pages: 129

Brand: Envipco Pages: 28

Brand: MERIT INDUSTRIES Pages: 30

Brand: Standard Pages: 58

Brand: MD SPORTS Pages: 29

Brand: LAUREL Pages: 7

BOOK FOLDER BF90+

Brand: Ricoh Pages: 24

APEX 5000 Series

Brand: Pyramid Pages: 17

Brand: Godrej Pages: 28

Brand: Dynisco Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands