background image

MOTOR MAINTENANCE

1) Contact your local ICE Distributor for any motor maintenance.
2) Check the motor brushes every 250 hours, Replace the brushes when they are worn to a   
     length of 10mm or less.

OPERATOR  MANUAL

ICE i18B/i18C

  

 11

MACHINE STORAGE

1) Always store the machine indoors and in its upright position.
2) Always store the machine in a dry area.
3) Always take off the pad driver / brush before storage. 

4) Always store the machine with the squeegee assembly raised off the floor.

5) If storing in an area which may reach freezing temperatures, be sure to drain all fluids from the 

 

    machine prior to storage(include the filter).  Any damage caused by freezing temperatures will not 

 

    be covered by the warranty.

6) Drain the recovery tank and keep the cover tank open so that it can "breathe" during storage.

7) Drain the solution tank of all fluid.

MONTHLY MAINTENANCE

1) Clean the battery tops to prevent corrosion (only for i18B).
2) Check for loose battery cable connections (only for i18B).
3) Inspect and clean the recovery tank cover seal. Replace it if damaged.
4) Lubricate all grease points and pivot points with silicon spay and approved grease.
5) Check the machine for loose nuts and bolts. 
6) Check the machine for leaks.

WARNNING: Batteries may emit hydrogen gas and an explosion or fire can 
result. Keep sparks and fire away from batteries at all times.

WARNNING: Whenever servicing batteries, be sure to wear protective gloves. 
Avoid contact with battery acid at all times.

BATTERY MAINTENANCE (ONLY FOR i18B)

Note: For the best machine performance, keep batteries charged at all times.Do not let them sit in a 
discharged condition.

1) Always follow the battery charging direction as outlined in the BATTERy CHARGING section of  
    this manual.
2) Keep battery tops and terminals free from corrosion. A strong solutin of baking soda and water is  
    the best way to keep the batteries corrosion free. DO NOT ALLOW THE BAKING SODA / WATER  
    SOLUTION TO ENTER THE BATTERy CELLS.
3) Use a wire brush with the baking soda solution to properly clean the battery posts and  
     connections. 
4) Check battery connections for wear and loose terminals. Replace them if necessary.  

Summary of Contents for I18B


































Reviews: