Ice i-synergy I20NBT-LA, Operator'S & Parts Manual

Page: 7 / 49

7 ICE i20NBL / i20NBTL / i20NBTL-OB / i24BTL
OPERATOR MANUAL
i-synergy
tm
collects operational data from
cleaning machines and transmit the information
to Ice’s server. the Ice server generates daily
reports and send them to designated end users
by email. from these reports, end users will
have information about machines’ usage and
even specific timings.
Besides, i-synergy
tm
also collects data on
lithium-ion battery, vacuum motor, brush
deck motor, transaxle, and other electrical
components at least once every minute when
the machine is in use and even during battery
charging.
i-synergy
tm
will send notifications instantly
to the Ice server in case of any malfunction.
Ice maintenance personnel will receive a
SmS within minutes from the Ice server for
immediate servicing.
uncRatInG macHIne
Be sure and check packing carton for any damage.
Immediately report any damage to carrier. Check
the contents of package to ensure that the
following items are included:
• Machine
• Lithium-ion Batteries
• Squeegee assembly
• Battery Charger
• Pad Driver
InStallInG BatteRIeS
the machine uses the lithium-ion batteries,
the batteries are already in the machine upon
delivery; However you will need to connect the
lithium ion batteries to the machine.
WaRnInG: fire or explosion Hazard.
Keep sparks and open flames away! Keep
battery compartment open when charging.
1. Turn off the machine.
2. Open recovery tank to gain access to battery
compartment.
3. Carefully place the Lithium-ion batteries into the
compartment. Place the battery brace at the
rear of the batteries.
do not dRop BatteRIeS Into
compaRtment!
4. Plug the batteries connector to the machine
adaptor, connect machine i-synergy
TM
COM
port with the batteries.
macHIne Set up
pRe-opeRatIon cHecKS
1. Sweep or dust mop the surface to be cleaned.
2. Check battery meter to make sure batteries are
fully charged. (See BATTERY CHARGING)
3. Check that squeegee is properly installed.
4. Check that brush / pad is properly installed.
InStallInG pad dRIVeR oR BRuSH
1. Ensure that the machine is turned off.
2. Step down on the scrub head lift pedal (see
machine components, item #26) to raise the
scrub head off the floor.
3. If using a Pad Driver, first attach the appropriate
pad to the pad driver surface.
4. Turn the brush motor hub until the slot with the
spring clip is visible through the scrub head
window.
5. Mount the pad driver or brush to the brush
motor hub by lining up the three studs with the
three holes in the brush motor hub. Once in the
holes, rotate the driver toward the spring clip to
lock the pad driver into place.
If necessary, press down on the motor hub lock
pin (see machine componts, item # 10)to lock
motor hub in place.
6. For Orbital head Model i20NBTL-OB, you need to
attach a rectangular, 20in(508mm)×14in(356mm)
Pad to the Orbital Pad driver. align the pad to the
Orbital pad driver, press from front-to-back and
side to side to alignment.
mountInG tHe SQueeGee aSSemBly
1. Lift the squeegee lift lever (see machine
components, item #33)to the upward position.
2. Mount the squeegee assembly to the squeegee
pivot bracket. make sure the knobs are
completely seated into the slots before securing
knobs.
3. Connect the vacuum hose to the squeegee
assembly. Loop the hose by using the hose clip
provided.
4. Check the squeegee blades for proper
adjustment.
MACHINE SET UP & INSTALLATION
i-synergy
tm
IntRoductIon