Ice-O-Matic GEM0650A/W Service And Installation Manual Download Page 15 | Manualshive

Page: 15 / 43

Ice-O-Matic GEM0650A/W Service And Installation Manual Download Page 15

GEM0650/0956/1256A/W

For the Installer

Page

9

Final Check List:

_______

1. Is the ice machine installed indoors in a location where the air and water temperatures are

controlled and where they do not exceed the design limitations?

_____2. Is there an electrical service disconnect within sight of the installed machine?

_____3. Has the voltage been checked and compared to the nameplate requirements?

_____4. Have all the plumbing connections been made and checked for leaks?

_____5. Is the ice machine and storage bin level?

_____6. Is there a minimum of 6 inches of clearance at the back of the machine for proper service

access and air circulation?

_____7. Is the water pressure a minimum of 20 psig?

_____8. Has the ice machine been secured to the bin?

_____9. Is there clearance over the top of the ice machine for service access?

____10. Is there a water shut off valve installed near the ice machine?

____11. Have all the shipping blocks been removed from the ice machine?

Insure the machine is level

Note: Fasten the ice machine

to the bin with the hardware

supplied with the ice machine

«
...
13
14
15
16
17
...
»

Summary of Contents for GEM0650A/W












































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands