IC Realtime ICIPS1300WDR Page 10 User Manual Download

Page: 10 / 41

Audio
Compression
Standard

G.711a/G.711u/PCM

Motion Detect

396 (18*22) detection zones

；

sensitivity level ranges from 1 to 6 (The 6

level has the highest sensitivity)
Activation event, alarm device, audio/video storage, image snapshot, log,
email function and etc.

Video

Camera
Masking

Sensitivity level ranges from 1 to 6. Each sensitivity level is the percentage of
the privacy mask zone.
Activation event, alarm device, audio/video storage, image snapshot, log,
email SMTP function and etc.

Alarm Input

1-channel input

，

1-channel output

Record
Priority

Manual>External alarm >Video detect>Schedule

Local Storage

Support local SD card hot swap

Record and

Backup

Storage
Management

Support display local storage status

Wire Network

1-channel wire Ethernet port, 10/100 Base-T Ethernet

Network
Protocol

Standard HTTP, TCP/IP, ARP, IGMP, ICMP, RTSP, RTP, UDP, RTCP, SMTP,
FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour, SNMP.

Network

Remote
Operation

Monitor, PTZ control, system setup, file download, log information,
maintenance , upgrade and etc

Video Output

1-channel analog video output

，

BNC port

Network
Interface

1-channel Ethernet, 10/100 Base-T Ethernet (The IPC-HF3110-F series
product has the optical port.)

3G Port

Support 3G SIM card, TD/EVDO/WCDMA function. (For 3G series product
only.)

Antenna Port

Support to receive the wireless signal (This function is for 3G and WIFI series
product only.)

AUX Interface

RS485 port

PTZ control interface. Support various protocols.

Power

Support AC24V/DC12V power and PoE. (The IPC-HF3110-F/W/E/T/C series
product

does not

support the PoE function.)

Power
Consumption

<10W (For WIFI and 3G device, it is below 12W.)

Working
Temperature

-10 ~+60

℃

(For –W device, it is from -10 ~+

℃

. For 3G device, it is from -

10 ~+

℃

)

Working
Humidify

10%~90%

Dimensions

70*63.2*149.5

Weight

650g

General Parameter

Installation

Support various installation modes

（

Enclosure and bracket is optional

）

1.3.2 Factory Default Setup

Please refer to the following sheet for factory default setup information.

Default Setup

Setup

Item

IPC-
HF3500

Series

IPC-
HF3300

Series

IPC-
HF3200

Series

IPC-
HF3100

Series

IPC-
HF3110
Series

IPC-
HF3101
Series

Brightness

mer

Con

ditio

Contrast

Summary of Contents for ICIPS1300WDR










































Search results

Summary of Contents for ICIPS1300WDR

Reviews:

Related manuals for ICIPS1300WDR

Brands by name

Popular brands

IC Realtime ICIPS1300WDR, User Manual

Search results

Summary of Contents for ICIPS1300WDR

Reviews:

Related manuals for ICIPS1300WDR

Brands by name

Popular brands