IC Realtime DVR704MSGV5 User Manual Download

Page: 16 / 144

2 Front Panel and Rear Panel

2.1 Front Panel

The front panel is shown as in Figure 2-1.

Figure 2-1

Please refer to the following sheet for detailed information.

Name

Port name and indicator light

USB port

USB port. To connect to mouse, or flash disk to backup data.

RJ45 network port

Network port.

Power indicator light

The red light is on when the device is running.

HDD indicator light

The blue light is on when there is HDD. The light is off when

there is no HDD.

Alarm indicator light

There is an alarm when the blue light is on.

6~9

Record indicator light 1~4

The blue light is on when system is recording.

Backup indicator light



The blue light is flashing when system is backup.



The blue light is on when the backup is finish.



The light is off when the backup error occurs or the flash

disk is removed.

GPS indicator light

Please note only the unit

of GPS module supports

this function.

The blue light is on when GPS function is normal.

3G indicator light

Please note only the unit

of 3G module supports

this function.

The blue light is on when 3G function is normal.

WIFI indicator light

Please note only the unit

The blue light is on when WIFI function is normal.

Summary of Contents for DVR704MSGV5

















































































































































Search results

Summary of Contents for DVR704MSGV5

Reviews:

Related manuals for DVR704MSGV5

Brands by name

Popular brands

IC Realtime DVR704MSGV5, User Manual

Search results

Summary of Contents for DVR704MSGV5

Reviews:

Related manuals for DVR704MSGV5

Brands by name

Popular brands