manualshive.com logo in svg

IC Realtime 1U POE NVR Series, User Manual, Page: 237 / 291

Share
Download
IC Realtime 1U POE NVR Series User Manual Download Page 237

4.12.4 Record Control

After setting the schedule for record or snapshot, make sure the recording stream (main by
default) or the snapshot function is set to auto. This ensures the NVR will follow the set
schedules accordingly. For detailed information, refer to "4.1.4.6.3 Record Control".

4.12.5 Disk Group

The installed HDD and any created RAIDs will default to Disk Group 1. You can set HDD group,
and HDD group setup for the main stream, sub stream, and snapshot operation in this section as
necessary.

If

Disk Quota is selected

is shown on the interface, click

Switch to Disk Group mode.

Step 1

Select

Main Menu > Advanced Settings > Storage Settings

>

Disk Group

.

The

Disk Group

interface will be displayed. See Figure 4-239.

Figure 4-239

Step 2

Select the group for each HDD group and then click

Apply

to save the settings. After

configuring HDD group, under the

Main Stream

tab,

Sub Stream

tab, and

Snapshot

tab, configure settings to save the main stream, sub stream, and snapshot to different
HDD groups as necessary.

4.12.6 Disk Quota

The disk quota function helps to allocate a fixed storage capacity for each channel and

226

Summary of Contents for 1U POE NVR Series




































































































































































































































































































Reviews:

No comments