manualshive.com logo in svg

IC Realtime 1U POE NVR Series, User Manual, Page: 227 / 291

Share
Download
IC Realtime 1U POE NVR Series User Manual Download Page 227

Parameter

Description

Interval (Sec.)

The NVR will not send emails caused by frequent alarm events of
the same type within the interval time

The value ranges from 0 to 3600. Select 0 disable interval.

Health Mail

The NVR can send a test email to check the connection at the
specified Inteval.

Sending Interval

This is the interval that the system sends a health test email.

The value ranges from 30 to 1440. 0 means that there is no
interval.

Test

Click

Test

to test the email sending function. If the configuration is

correct, the receiver’s email account will receive the email.

Before testing, click

Apply

to save the settings.

Step 3

Click

Apply

to complete the settings.

4.11.7 SNMP

SNAMP allows the NVR to be managed by a database such as a MIB. Once configured, you
can utlize software such as MIB Builder and MG-SOFT MIB Browser to manage and control
the NVR from the software.

Prerequisites

● Install the software that can manage and control the SNMP, such as MIB Builder and

MG-SOFT MIB Browser

● Obtain the MIB files that correspond to the current version from the technical support.

This function is not supported in all NVR models.

Procedure

Step 1

Select

Main Menu

>

Advanced Settings

>

NETWORK

>

SNMP

.

The SNMP interface will be displayed. See Figure 4-230.

Figure 4-230

216

Summary of Contents for 1U POE NVR Series




































































































































































































































































































Reviews:

No comments