manualshive.com logo in svg

IC Realtime 1U POE NVR Series, User Manual, Page: 224 / 291

Share
Download
IC Realtime 1U POE NVR Series User Manual Download Page 224

4.11.5 UPnP

This function allows communication between the NVR and the router to enable port mapping
and forwarding. You will need to have a UPnP-enabled router for this configuration.

4.11.5.1 Configuring the Router

You may need to refer to your router's manual or contact the ISP regarding any
information on configuring your router.

Step 1

Log in to the router using a web browser. On most residential routers, type in the
default gateway IP in the address bar and press enter.

Step 2

Enable the UPnP function on the router.

Step 3

Connect the Device with the LAN port on the router to connect into the LAN.

Step 4

Select

Main Menu

>

Advanced Settings

>

NETWORK

>

TCP/IP

, configure the

IP address into the router IP address range, or enable the DHCP function to obtain an IP
address automatically.

4.11.5.2 Configuration UPnP

Step 1

Select

Main Menu

>

NETWORK

>

UPnP

.

The

UPnP

interface will be displayed. See Figure 4-227.

Figure 4-227

Step 2

Configure the settings for the UPnP parameters. See Table 4-69.

213

Summary of Contents for 1U POE NVR Series




































































































































































































































































































Reviews:

No comments