manualshive.com logo in svg

IC Realtime 1U POE NVR Series, User Manual, Page: 212 / 291

Share
Download
IC Realtime 1U POE NVR Series User Manual Download Page 212

4.9.3.3 Network Test

You can test the network connection status between the NVR and other devices.

Step 1

Select

Main Menu

>

Info

>

Network

>

Test

.

The

Test

interface will be displayed. See Figure 4-207.

Figure 4-207

Step 2

In the

Destination IP

box, enter the IP address.

Step 3

Click

Test

.

After testing is completed, the test result will display information for the average delay,
packet loss, and network status.

4.9.4 Maintenance and Management

4.9.4.1 Device Maintenance

You can can configure the auto reboot for periodical maintenance of the NVR. It is
recommended to reboot at least once a week. You can also configure the case fan mode to
reduce noise and extend the service life.
Step 1

Select

Main Menu

>

Advanced Settings

>

System Operation

>

Maintenance >

Scheduled Maintenance

.

The

Maintenance

interface will be displayed. See Figure 4-208.

201

Summary of Contents for 1U POE NVR Series




































































































































































































































































































Reviews:

No comments