IC Realtime 1U POE NVR Series User Manual Download Page 198

Page: 198 / 291

Figure 4-189

Step 2

To configure the settings for the PIR alarm parameters, see "4.8.5.1 Motion
Detection".

Step 3

Click

Apply

to complete the settings.

● Click

Default

to restore the default setting.

● Click

Copy to

, in the

Copy to

dialog box, select the additional channel(s) that you

want to copy the motion detection settings to, and then click

Apply

4.8.6 Audio Detection

The NVR can generate an alarm if it detects abnormal or audio volume changes.
Step 1

Select

Main Menu

Advanced Settings

Alert Center

Video Detection

Audio Detection

Step 2

Configure parameters. See Table 4-56.

Table 4-56

Parameter

Description

Channel

In the Channel list, select a channel to set.

Audio Exception

Check the box here, the NVR can generate an alarm once the
audio input is abnormal.

Intensity change

Check the box here, the NVR can generate an alarm once the
audio volume becomes strong.

Period

Define a period during which the function is active.

187

Summary of Contents for 1U POE NVR Series




































































































































































































































































































Search results

Summary of Contents for 1U POE NVR Series

Reviews:

IC Realtime 1U POE NVR Series, User Manual, Page: 198 / 291

Search results

Summary of Contents for 1U POE NVR Series

Reviews: