manualshive.com logo in svg

IC Realtime 1U POE NVR Series, User Manual, Page: 164 / 291

Share
Download
IC Realtime 1U POE NVR Series User Manual Download Page 164

Parameter

Description

Tour

Click to select the check box and then select the channel(s) for
the tour. When the event is triggered, the local interface of the
NVR device will display the selected channel(s) on the screen.

● you will need to set the time interval and mode for tour

prior, see "4.17.2 Tour".

● After the tour ends, the previous screen split mode

will resume.

Log

Select the check box, the NVR device records the alarm
information in the log when an event  occurs.

Voice Prompts

Check the box and then select the corresponding audio file from
the dropdown list. The NVR will play the audio file when the
event occurs.

Refer to "4.18.1 File Management" to add the audio file first.

Buzzer

Select the check box to activate the onboard buzzer when an event
occurs.

Step 3

Click

Apply

to complete the setup.

4.7.2.7 People Counting

When using a People Counting supported camera with a supported NVR, the video analysis
technology can calculate the number of people exiting or entering the specified zone on the video.
The NVR can then generate an event when the amount has exceeded the threshold.

4.7.2.7.1 People Counting

Step 1

Select

Main Menu > Advanced Settings > Alert Center

>

Parameters

>

People Counting

>

People Counting

.

The

People Counting

interface will be displayed. See Figure 4-160.

153

Summary of Contents for 1U POE NVR Series




































































































































































































































































































Reviews:

No comments