background image

 

6

 

 

 

For materials which are not listed, please request information from manufacturer/supplier.  

 

Before using other method for cleaning or decontamination, the user must ascertain with the manufacturer/supplier 
whether this method will not harm the instrument.  

 

Wear the proper protective gloves during cleaning of the instrument. 

 
 

 

Note: 

• Electrical instruments may not be placed in the 

cleansing agent. 

•  The  instrument  is  a  sophisticated  electronic 

product; please avoid severe shaking during use 
and transportation. 

• The instrument must be cleaned and put it into 

the initial packaging  carton before sending for 
service, avoid contamination. 

• Switch OFF the instrument and put it in a dry, 

clean,  stable  place  at  room  temperature  in 
long-term disuse. 

 

7.

 

Associated Standards and Regulations 

 

Construction in accordance with the following safety 
standards: 
EN 61010-1 
Construction in accordance with the following EMC 
standards: 
EN 61326-1 
Associated EU guidelines: 
EMC-guidelines: 2004/108/EC 
Instrument guidelines: 73/023/EWG 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for V05












Reviews: