background image

 

1

 

 

 

Electronic circulator pump operating manual:  

BETA 25-60 

 

CAUTION  Prior  to  operation,  please  read  this  operating 
manual.  Due  to  safety  reasons,  the  use  of  this  equipment 
requires a thorough knowledge of this operating manual.  

 

 CAUTION  This  operating  manual  is  the  primary  basis  for  the 
equipment’s  sale  contract.  Non-observance  of  the  recommendations 

listed  in  this  manual  will  result  in  a  breach  of  this  contract  and  will 
invalidate  any  claims  made  by  the  user  relating  to  the  equipment’s  failure 
resulting from its inappropriate use. 

   

 CAUTION  Non-observance  of  recommendations  listed  in  this 
operating manual may result in personal injuries or damage to 
units  where  the  equipment  is  installed,  the  environment  or  the 

pump itself.   

 
CAUTION!  Children  and  persons  with  reduced  physical, 
sensory  or  mental  capabilities  must  not  use  this  equipment; 
also  persons  with  no  experience  or  knowledge  of  the  product 

unless  under  the  supervision  or  in  accordance  with  the  equipment’s 
operating  manual  and  instructed  by  a  person  responsible  for  their  safety. 
Children must not play with this equipment. 

  

Summary of Contents for BETA 25-60










Reviews: