IBM TotalStorage 3534-F08 Installation Manual Download Page 43

Page: 43 / 81

Chapter 5. Replacing an SFP

To replace a small form-factor pluggable (SFP) device, you first remove the existing
SFP, and then install a new one. This chapter contains these procedures.

Note: Simple network management protocol (SNMP) traps are generated when you

remove and install an SFP. You do not need to unplug the switch to replace
an SFP.

Figure 13 shows an IBM SFP.

Time required

Approximately 20 seconds to remove and install an SFP.

Items required

None.

Note: This is a hands-only operation.

Removing an SFP

Complete the following steps to remove an SFP:

1. Pull forward on the tab on the front of the SFP.

2. Pull out the SFP.

3. Carefully move the SFP from side to side to unseat it.

SJ000317

Figure 13. IBM SFP

Summary of Contents for TotalStorage 3534-F08


















































































Search results

Summary of Contents for TotalStorage 3534-F08

Reviews:

Related manuals for TotalStorage 3534-F08

Brands by name

Popular brands

IBM TotalStorage 3534-F08, Installation Manual

Search results

Summary of Contents for TotalStorage 3534-F08

Reviews:

Related manuals for TotalStorage 3534-F08

Brands by name

Popular brands