background image

 

Creating a hibernation file

  Attention 

When you start the system with the

 Hibernation Utility for Standalone Boot diskette, be sure

not to choose the Create Partition option. If you do so, your hard disk will quit working, and
you will have to take it to an IBM reseller or marketing representative for reformatting. Thus all
of the data on the hard disk will be lost.

The following instructions are for those using operating systems other than Windows 2000.

If you want to suspend operation but keep your work exactly as it is, so that you can resume
operation at the same point later, you can put your computer in hibernation mode.

To use the hibernation mode, you need to create a hibernation file with ThinkPad Configuration
Program. This file can be created on a single-partitioned or multiple-partitioned hard disk drive,
and is subject to the following restrictions:

Ÿ

It must be created on the primary hard disk drive.

Ÿ

All partitions must be formatted before you create the hibernation file.

Ÿ

The partitions must be formatted in either FAT16 or FAT32; you cannot use NTFS, the default
file system for Windows NT.

   

 

3

Summary of Contents for THINKPAD A20M

















Reviews: