background image

Appendix C. Parts listing

This section contains FRU part number information.

How to use the FRU catalog

This parts listing contains reference drawings and a corresponding index for all field replaceable parts. The
index provides the part number, the quantity required (units), and a description of the part.

Listed below is additional information about the parts assembly index.

SIMILAR ASSEMBLIES

If two assemblies contain a majority of identical parts, they are broken down on the same list.
Common parts are shown by one index number. Parts specific to one or the other of the
assemblies are listed separately and identified by description.

AR

(As Required) in the Units column indicates that the quantity is not the same for all machines.

NP

(Non-Procurable) in the Units column indicates that the part is non-procurable and that the
individual parts or the next higher assembly should be ordered.

NR

(Not Recommended) in the Units column indicates that the part is procurable, but not
recommended for field replacement, and that the next higher assembly should be ordered.

R

(Restricted) in the Units column indicates the part has a restricted availability.

INDENTURE

The indenture is marked by a series of dots located before the parts description. The indenture
indicates the relationship of a part to the next higher assembly.

No Dot

Main assembly

One Dot

Detail parts of a main assembly

One Dot

Subassembly of the main assembly

Two dots

Detail part of a one-dot subassembly

Two dots

Subassembly of a one-dot subassembly

Three dots

Detail part of a two-dot subassembly

© Copyright IBM Corp. 2010

79

Summary of Contents for SureMark 4610 1NF

















































































































Reviews: