IBM SureMark 4610 1NF Page 43 Hardware Service Manual Download | Manualshive

Page: 43 / 112

background image

4. Grasp the tray just below the fiscal screw and pull it out of the printer.

5. Place the fiscal tray in a safe location for future use. For information on removing the fiscal logic card

from the tray, see “Removing the fiscal logic card” on page 31.

Installing the fiscal tray

This section provides information for installing and IBM fiscal tray in the printer. For information on how to
install a fiscal tray in a fiscal ready printer with an IBM business partners fiscal solution installed, see the
documentation provided by the IBM business partner.

To install the fiscal tray, complete the following steps:

1. Orient the printer so that the opening for the fiscal tray is facing you.

2. Align the rails on the fiscal tray with the slots in the printers cover.

3. Slide the fiscal tray into the printer until is stops.

A

Figure 8. Removing the fiscal tray

Removing and replacing FRUs

Chapter 5. Removing and replacing FRUs

29

«
...
41
42
43
44
45
...
»

Summary of Contents for SureMark 4610 1NF

















































































































Reviews:

No comments

Related manuals for SureMark 4610 1NF

Brand: m3d Pages: 23

Brand: m3d Pages: 26

Magicolor 2 plus

Brand: QMS Pages: 90

Magicolor 2 Desklaser

Brand: QMS Pages: 4

Brand: QMS Pages: 8

Brand: QMS Pages: 94

Brand: QMS Pages: 6

Brand: BCS Pages: 151

Brand: Kodak Pages: 2

CR10 XZ (Belt Z)

Brand: ExoSlide Pages: 12

wematter Atmosphere

Brand: 3D Systems Pages: 11

ORCABOT XXL PRO2

Brand: PRODIM Pages: 41

WorkCentre 6400XF

Brand: Xerox Pages: 24

Bravo se Disc Publisher

Brand: Primera Pages: 58

Brand: Custom Audio Electronics Pages: 88

Brand: SIGN RACER Pages: 73

imageRUNNER ADVANCE DX 717 Series

Brand: Canon Pages: 98

Oce VarioPrint 6000 Ultra+ Series

Brand: Canon Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands