IBM SureMark 4610 1NF Page 45 Hardware Service Manual Download | Manualshive

Page: 45 / 112

background image

Removing the fiscal logic card

This section provides the information needed to remove the fiscal logic card from a fiscal tray provided by
IBM. If your fiscal solution is provided by an IBM business partner, see the documentation provided by the
IBM business partner for more information. The fiscal logic card is the logic card installed in the fiscal logic
tray and should not be confused with the logic card that is installed on the printer unit under the main
cover.

Note:

It is not necessary to remove the program memory from the logic card to complete the steps. It is
necessary to remove the screw that secures the program memory.

To remove the fiscal logic card, complete the following steps:

1. Place the fiscal tray on a clean, flat, static-protective surface.

2. Remove the electronic journal card from the card slot and set it aside for future use.

Removing and replacing FRUs

Chapter 5. Removing and replacing FRUs

31

«
...
43
44
45
46
47
...
»

Summary of Contents for SureMark 4610 1NF

















































































































Reviews:

No comments

Related manuals for SureMark 4610 1NF

870 - SuperScript B/W Laser Printer

Brand: NEC Pages: 52

SuperScript 1800

Brand: NEC Pages: 8

Brand: Olivetti Pages: 78

System 2200 2231w-3

Brand: Wang Pages: 52

Multi-Font NX-2415

Brand: Star Micronics Pages: 134

Fast T-Jet Blazer Pro

Brand: Screen Print & Inkjet Pages: 138

Brand: Oce Pages: 61

Printpix NC-400D

Brand: FujiFilm Pages: 47

ApeosPort C5570

Brand: Fuji Xerox Pages: 290

Brand: Ricoh Pages: 849

imageRUNNER ADVANCE DX 717 Series

Brand: Canon Pages: 98

Oce VarioPrint 6000 Ultra+ Series

Brand: Canon Pages: 56

Brand: Canon Pages: 188

imageRUNNER ADVANCE C356iF III

Brand: Canon Pages: 96

Brand: Canon Pages: 218

Brand: Star Micronics Pages: 73

Brand: Canon Pages: 2

WORKCENTRE 7755

Brand: Xerox Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands