![background image](http://html1.mh-extra.com/html/ibm/storage-networking-san128b-6/storage-networking-san128b-6_installation-service-and-user-manual_3517001063.webp)
4
4
460400
id
N32
Online
FC
F-Port
10:00:8c:7c:ff:5c:c5:01
5
5
460500
id
N32
Online
FC
F-Port
10:00:8c:7c:ff:58:4c:00
6
6
460600
id
N32
Online
FC
F-Port
10:00:8c:7c:ff:5c:c9:01
7
7
460700
id
N32
Online
FC
F-Port
10:00:8c:7c:ff:5c:bd:00
8
8
460800
--
N32
No_Module
FC
9
9
460900
--
N32
No_Module
FC
10
10
460a00
--
N32
No_Module
FC
11
11
460b00
--
N32
No_Module
FC
12
12
460c00
--
N32
No_Module
FC
13
13
460d00
--
N32
No_Module
FC
14
14
460e00
--
N32
No_Module
FC
15
15
460f00
--
N32
No_Module
FC
16
16
461000
--
N32
No_Module
FC
17
17
461100
--
N32
No_Module
FC
18
18
461200
--
N32
No_Module
FC
19
19
461300
--
N32
No_Module
FC
20
20
461400
--
N32
No_Module
FC
21
21
461500
--
N32
No_Module
FC
22
22
461600
--
N32
No_Module
FC
23
23
461700
--
N32
No_Module
FC
<Output truncated>
Backing up the configuration
About this task
It is recommended that you back up the configuration on a regular basis to ensure that a complete
configuration is available for downloading to a replacement switch.
Procedure
1.
Log in to the device as the admin user.
2.
Back up the device configuration to an FTP server by entering the
configUpload
command and
following the prompts.
sb_70:admin> configupload
Protocol (scp, ftp, local) [ftp]:
Server Name or IP Address [host]: 192.168.0.100
User Name [user]: anonymous
Path/Filename [<home dir>/config.txt]: /dumps/supportsave/pz/switch85/G20-1.txt
Section (all|chassis|switch [all]): all
configUpload complete: All selected config parameters are uploaded
This command uploads the device configuration to the server, making it available for downloading to
a replacement device if necessary.
Note:
If Virtual Fabrics (VF) is enabled, you must enter
configUpload
for each VF separately.
Powering down the device
About this task
Complete the following steps to power down the device.
Procedure
1.
Shut down the Fabric OS software using the
sysShutdown
command.
2.
Identify the power-on switches in the nonport-side of the device.
3.
Power off both power supplies by setting each power switch to the “O” position.
4.
Unplug the power cables from the power source before servicing the device or FRUs.
Initial Setup and Verification
43
Summary of Contents for Storage Networking SAN128B-6
