IBM Slicestor 3448 Manual Download Page 46

Page: 46 / 52

Table 33. General specifications (Accesser 4105)

A4105

Specification

Operating Temperature °C (°F)

10 to 35 degrees °C (50-95 degrees °F)

Non - operating temperature °C (°F)

-40 to 65 degrees °C (-40-158 °F)

Operating humidity

10-80%

Non - operating humidity

5-90%

Dimensions without front bezel (W x D x H)

17.250 x 26.125 x 1.750 (in)

43.815 x 66.3575 x 4.445 (cm)

Dimensions with front bezel (W x D x H)

19.000 x 27.625 x 1.750 (in)

48.26 x 70.1675 x 4.445 (cm)

Weight

30.1 (lbs)

13.65313 (kg)

Rail/extended

27.5/34.5 (in)

69.85/87.63 (cm)

Power cord

C14/C13 (connector) 2 m (length)

Input power options

Voltage Range 100-240 V AC, FREQUENCY 50-60hz

2 hot-swappable 750W PSUs in 1+1 configuration

Table 34. Power measurements for Accesser 4105

100v

240v

Power(W)

OFF

0.85

0.26

START

320

0.92

FULL

240

0.99

240

0.94

IBM Cloud Object Storage System: Slicestor 3448 Appliance Maintenance Manual 3409-S02/3401-S02/3403-S02

Summary of Contents for Slicestor 3448





















































Search results

Summary of Contents for Slicestor 3448

Reviews:

Related manuals for Slicestor 3448

Brands by name

Popular brands

IBM Slicestor 3448, Manual

Search results

Summary of Contents for Slicestor 3448

Reviews:

Related manuals for Slicestor 3448

Brands by name

Popular brands