IBM P260 Installation And Service Manual Download Page 508 | Manualshive

Page: 508 / 524

background image

Committing the TEMP system firmware image

After updating the system firmware and successfully starting the compute node from the temporary
(TEMP) image, copy the TEMP image to the permanent (PERM) image by using the diagnostics program
commit function.

About this task

Note:

If you install the compute node firmware update permanently by committing the temporary

firmware level from the temporary side to the permanent side, the temporary and permanent sides
contain the same level of firmware. You cannot return to the level that was previously on the permanent
side.

Procedure

1.

Load the diagnostics program. See “Running the diagnostics program” on page 453.

2.

From the Function Selection menu, select Task Selection and press Enter.

3.

From the Tasks Selection List menu, select Update and Manage System Flash and press Enter.

4.

From the Update and Manage System Flash menu, select Commit the Temporary Image and press
Enter.

5.

When the commit function is complete, press F3 until the Diagnostic Operating Instructions window
is displayed. Then, press F3 again to exit the diagnostic program.

Solving shared IBM Flex System Enterprise Chassis resource
problems

Problems with shared resources might appear to be in the compute node, but might actually be a
problem in a IBM Flex System Enterprise Chassis component.

About this task

This information provides procedures to help you isolate compute node problems from shared resource
problems.

If the problem is thought to be with a shared resource, see the following documentation for additional
information:

v

Problem Determination and Service Guide for your IBM Flex System Enterprise Chassis

v

Hardware Maintenance Manual and Troubleshooting Guide for your IBM Flex System Enterprise Chassis

v

If the problem cannot be solved, see “Solving undetermined problems” on page 498.

To check the general function of shared resources, complete the following steps:

Procedure

1.

Verify that the required power modules are installed in the IBM Flex System Enterprise Chassis and
that the chassis is connected to a working power source.

496

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

«
...
506
507
508
509
510
...
»

Summary of Contents for P260













































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P260

Brand: Rae Pages: 71

Brand: A&D Pages: 16

Brand: A&D Pages: 50

Brand: A&D Pages: 20

Brand: A&D Pages: 14

Brand: A&D Pages: 3

Brand: A&D Pages: 42

Brand: A&D Pages: 2

ESSENTIAL UB-525

Brand: A&D Pages: 48

51MP392H - 51" Widescreen Hd Ready Tv

Brand: Magnavox Pages: 7

SyncMaster 753 DFX

Brand: Samsung Pages: 82

Brand: Samsung Pages: 44

Brand: ACO Pages: 4

ThinkVision L190N

Brand: IBM Pages: 42

Brand: Siko Pages: 2

KOT-0150US-SA4W

Brand: K&JAD Technology Pages: 19

Brand: AOC Pages: 48

Brand: ViewSonic Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands