11. Using the appropriate brackets or rails, mount the
drive with any side or end in a vertical or horizontal
position. (Do not mount the drive in a tilted position.)
12.
Ensure proper routing of the cable(s).
13.
Retrieve any loose screws or parts from within the
computer.
14. Verify all settings and replace the cover.
15. Plug in your computer. Do not turn it on.
16. Insert the DriveGuide or OS setup diskette in the
floppy drive.
17. Turn on the computer.
18. Boot your system.
Ÿ
If the system boots up, turn off your computer
and replace the cover.
Ÿ
If the system does not boot up, check all
settings.
Ÿ
If the system still fails to boot up, remove the
new drive to return the system to its original
configuration. Call the IBM Hard Disk Drive
Technical Support Center.
19. Set the BIOS options of your computer system to
Auto Detection and LBA mode if available. Key
sequences for accessing your BIOS can be found
in your computer system manual. The following
chart lists true LBA sector counts and drive
capacities. Translated schemes are derived from
the LBA count of a drive.
9GB
63
16
16,383
DJNA-370910
13.5GB
63
16
16,383
DJNA-371350
18GB
63
16
16,383
DJNA-371800
22GB
63
16
16,383
DJNA-372200
10GB
63
16
16,383
DJNA-351010
15GB
63
16
16,383
DJNA-351520
20GB
63
16
16,383
DJNA-352030
25GB
63
16
16,383
DJNA-352500
Capacity
Sector
/Track
Heads
Cylinders
IBM model
number
Partitioning and formatting
Partition and format your drive with one of these two
methods:
DriveGuide
1.
Boot the DriveGuide installation utility.
2.
If the DriveGuide configuration matches your new
system configuration, continue. If the system con-
figuration is not a match, or you want to proceed
manually, select no. Then verify BIOS settings,
cabling, and jumpers and run DriveGuide again.
3.
Drive Guide determines available partition sizes
based on the operating system to be installed.
Select the partition sizes for your installation.
4.
Click “Finish” to complete the partitioning and
formatting of your drive.
FDISK.EXE and FORMAT.EXE (or a similar partitioning
software from your operating system)
1. Follow the instructions provided with your operating
system to partition the drive. If FDISK.EXE does not
recognize more than 8.4 gigabytes and your drive is
larger than 8.4 gigabytes, your BIOS may not be
supporting Interrupt 13 Extensions.
2. Format the drive by following the instructions pro-
vided with FORMAT.EXE. Formatting will verify the
hard disk media and create file allocation tables for
the partition.
Install an operating system. Consult your operating
system manual.
For additional information on the drive and its instal-
lation see
http://www.storage.ibm.com/hardsoft/diskdrdl/
prod/deskstar.htm
®
© International Business Machines Corporation 1999
www.ibm.com/harddrive
IBM Hard Disk Drive Technical Support Center
Dept. WCN
3605 Highway 52 North
Rochester, MN 55901
Telephone: 888.IBM.5214 or 507.286.5825
Fax: 507.253.DRIVE
E-mail: [email protected]
Singapore Technical Support Center
Telephone: (65)6418.9595 or 1800.418.9595
E-mail: [email protected]
IBM Systems Storage Division
5600 Cottle Road
San Jose, CA 95193
www.ibm.com/storage
Printed in the United States of America
09-99
All Rights Reserved
IBM is the registered trademark of International Business Machines Corporation.
Other company, product, and service names may be trademarks or service marks of others.
Produced by the IBM Hard Disk Drive Technical Support Center.
OEM Hard Disk Drive Specifications for DJNA-3xxxxx, revision 1.0
Product Description data represents IBM’s design objectives and is provided for comparative
purposes; actual results may vary based on a variety of factors. This product data does not
constitute a warranty. Questions regarding IBM’s warranty terms or methodology used to
derive this data should be referred to the IBM Hard Disk Drive Technical Support Center.
Data subject to change without notice.
Date: 01 September 1999
IBM storage products
Page 2
IBM Hard Disk Drive Technical Support Center version 4.0