background image

Connectors

The electrical connectors are located as
shown.

Pin 1

Electrical Connectors (rear view) 80 Pin SCA models

Power Pin 1

4 3 2 1

Pin 2

Pin 35

SCSI Pin 1

Aux Connector Pin 1

Electrical Connectors (rear view) 68 Pin models

4 3 2 1

Power Pin 1

SCSI Pin 1

Electrical Connectors (rear view) 50 Pin models

Pin 1

(15X)2 mm

2.54 mm*

Jumper Pin locations (front view) - all models
* Not available on 80 Pin SCA

Note: See  electrical interface specifications

for power pin assignment.

The DC power connector is designed to mate 

with AMP part 1-480424 (using AMP pins P/N
350078-4).  Equivalent connectors may  be
used.
Pin assignments are shown below, as viewed
from the end of the drive.

4

3

2

1

Pin

Voltage

1

+12 V

2

GND

3

GND

4

+5  V

Option Block

Jumper Settings
Jumper position and function are as shown below.  Pin pitch is 2mm.
Termination power enable 2.54mm pitch.

0

1

Reserved

Reserved

10 12 14 16 18

Ground

Ground

Ground

Termination 
Power Enable

1

3

5

7

11 13 15 17 19 21 23 25 27 29 31

2

4

6

8

20 22 24 26 28 30 32

Enable Active Termination

+5V

2

SCSI 
Address

Not 
Used

Blank

Ground

External Activity LED

Write Protect

Auto Start Delay

Disable Sync Negotiations

Disable SCSI Parity

Disable Unit Attention

Reserved

Reserved

Reserved

Auto Start

50 Pin Single Ended Front Option Block and TermPower Block.

Reserved

Reserved

Ground Ground

Ground

Termination 
Power Enable

1 3

5

7

11 13 15 17 19 21 23 25 27 29 31

2 4

6

8 10 12 14 16 18 20 22 24 26 28 30 32

Enable Active Termination

+5V

0

1

2

SCSI Address

Blank

Auto Start

Ground

External Activity LEDWrite Protect

Auto Start Delay

Disable Sync Negotiations

Disable SCSI Parity

Disable Unit Attention

3

Disable Wide 
Negotiations

Reserved

Reserved

68 Pin Single Ended Front Option Block and TermPower Block.
68 Pin Differential Option Jumper Block.

Ground

Ground

1 3

5

7

11 13 15 17 19 21 23 25 27 29 31

2 4

6

8 10 12 14 16 18 20 22 24 26 28 30 32

+5V

0

1

2

SCSI Address

Blank

Auto Start

Ground

External Activity LED

Write Protect

Auto Start Delay

Disable Sync Negotiations

Disable SCSI Parity

Disable Unit Attention

3

Disable Wide 
Negotiations

Reserved

Reserved

Reserved

80 Pin SCA-2 Front Option Jumper Block.

Summary of Contents for DGHS-318220










Reviews: