IBM CS821 Service Manual Download Page 76 | Manualshive

Page: 76 / 118

background image

b.

After the system processor module is properly aligned, press the top of the pen to release it from
the processor. Lift the pen off the processor.

5.

If either the TIM or the heat sink is damaged, replace both the TIM and the heat sink. The TIM is
pre-applied to the heat sink. Carefully lower the heat sink over the system processor module,
ensuring that the holes in the heat sink (A) align with the two guide pins (B) on the socket, as shown
in Figure 71.

Figure 70. Lowering the processor into the socket

Figure 71. Installing the heat sink

60

Power Systems: Servicing the IBM Power System S821LC (8001-12C) or the IBM CS821 (8005-12N)

«
...
74
75
76
77
78
...
»

Summary of Contents for CS821























































































































Reviews:

No comments

Related manuals for CS821

Brand: MAKER MADE Pages: 14

Brand: National Flooring Equipment Pages: 44

Brand: Earlex Pages: 12

Brand: Earlex Pages: 12

Brand: Earlex Pages: 4

Brand: Earlex Pages: 4

Brand: Q-tran Pages: 5

Brand: RAMSET Pages: 16

Brand: FASTER TOOLS Pages: 12

Brand: OCZ Pages: 8

Brand: Samlexpower Pages: 24

Brand: TP-Link Pages: 59

GEN 8-400 ABCDE

Brand: TDK-Lambda Pages: 96

Brand: Altronix Pages: 4

Brand: Hach Pages: 32

Brand: El-Björn Pages: 2

Brand: Baileigh Industrial Pages: 20

Brand: Worcraft Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands