I. Specifications
Rated Voltage: 12V (9-16V)
Rated Current: 20mA~200mA
Detecting Distance: Rear (0’ – 5’) Front (0’- 2.5’)
Ultrasonic Frequency: 40Khz
Working Temperature: -22°~176°F
II. Connection
1) Sensors should be 1.5 to 2.5 feet from the ground,
and 4” to 7” inches apart from each other
(depending on vehicle application).
2) Install parking sensors by drilling holes out of the
back bumper with the supplied 21mm hole saw
I. Specifications
Rated Voltage: 12V (9-16V)
Rated Current: 20mA~200mA
Detecting Distance: Rear (0’ – 5’) Front (0’- 2.5’)
Ultrasonic Frequency: 40Khz
Working Temperature: -22°~176°F
II. Connection
1) Sensors should be 1.5 to 2.5 feet from the ground,
and 4” to 7” inches apart from each other
(depending on vehicle application).
2) Install parking sensors by drilling holes out of the
back bumper with the supplied 21mm hole saw
bit (make sure the thicker side of the sensor is
facing down, level with the ground and the UP
arrow on the back of the sensor is facing up), and
install parking sensors.
3) The rear sensors A/B/C/D should be installed from
left to right (looking at the bumper). This is also
how they should be plugged into the control box.
(Example A: left, B: mid-left, C: mid-right, D: right)
4) Connect the RED wire to the +12 volt accessory wire.
5) Connect the BLUE wire to the +12 volt reverse light wire.
6) Connect the BLACK wire to a ground (a metal,
non-painted surface).
7) Plug that wiring harness into the parking sensor
control box (labeled power).
8) Run the audible warning device cable through
the vehicle and mount somewhere in vehicle’s
cabin where the device can be clearly heard with
no obstructions (avoid placing cable where it can
get pinched or damaged) and plug cable into the
control box.
9) Mount the control box in rear of vehicle in a safe
place away from rain, heat or humidity.
NOTE:
1) The parking sensors are designed to be
used in vehicles with metal bumpers.
2) The parking sensor kit is used as a parking aid.
Please use your mirrors and look around to
avoid hitting any object.
bit (make sure the thicker side of the sensor is
facing down, level with the ground and the UP
arrow on the back of the sensor is facing up), and
install parking sensors.
3) The rear sensors A/B/C/D should be installed from
left to right (looking at the bumper). This is also
how they should be plugged into the control box.
(Example A: left, B: mid-left, C: mid-right, D: right)
4) Connect the RED wire to the +12 volt accessory wire.
5) Connect the BLUE wire to the +12 volt reverse light wire.
6) Connect the BLACK wire to a ground (a metal,
non-painted surface).
7) Plug that wiring harness into the parking sensor
control box (labeled power).
8) Run the audible warning device cable through
the vehicle and mount somewhere in vehicle’s
cabin where the device can be clearly heard with
no obstructions (avoid placing cable where it can
get pinched or damaged) and plug cable into the
control box.
9) Mount the control box in rear of vehicle in a safe
place away from rain, heat or humidity.
NOTE:
1) The parking sensors are designed to be
used in vehicles with metal bumpers.
2) The parking sensor kit is used as a parking aid.
Please use your mirrors and look around to
avoid hitting any object.
A B C D
A B C D
Displa
y P
ow
er
Red Wire: 12 Volt Accessory (+)
Blue Wire: Reverse Light (+)
Gray Wire: Brake Light (+)
Black Wire: Ground
Ad
j
A B C D
A B C D
Displa
y P
ow
er
Red Wire: 12 Volt Accessory (+)
Blue Wire: Reverse Light (+)
Gray Wire: Brake Light (+)
Black Wire: Ground
Ad
j
