iBeam TE-360-3D Installation Instructions Manual Download Page 6 | Manualshive

Page: 6 / 16

iBeam TE-360-3D Installation Instructions Manual Download Page 6

1.800.221.0932

|

iBEAMUSA.com

6

Camera calibration parameter settings:

  •  Press the “Mode” button to access the settings menu. The default password is “360”.
  •  Enter the Camera Calibration menu.
  •  Enter 360 Tuning to access the parameter settings.
  •  Select the correct size of the vehicle and adjust the vehicle position as needed.
  •  Adjust the shadow area for each of the cameras as needed. Each increment is equal to 2-inches.

The shadow area will help to eliminate the vehicle from being portrayed in the final image for

applications where it is not possible to angle the cameras away from the vehicle.

• Adjust the merging angle and range as needed. Try to keep this setting as close to default

as possible. Adjusting this too much will distort the seamed image. The merging angle is to
be used for instances where the front or rear camera image does not meet up with the side
camera image. The merging range is for adjusting the side cameras.

Continued on the next page

CAMERA CALIBRATION

(CONT.)

«
...
4
5
6
7
8
...
»

Summary of Contents for TE-360-3D

















Reviews:

No comments