IBC Water AS1041MP-CL, Installation & Operating Instructions Manual

Page: 25 / 54

AS1041MP-CL Page
25
WS1EI Manual
Control Valve Function and Cycles
of Operation
This glass filled Noryl
1
(or equivalent) fully automatic
control valve is designed as the primary control
center to direct and regulate all cycles of a water
softener. The control valve can be set to regenerate
on demand (consumption of a predetermined amount
of water) and/or as a time clock (passage of a
particular number of days). The control valve is
factory set to regenerate on demand consumption
with a delay regeneration set for 2am.
The control valve is compatible with a variety of resin
cleaners. The control valve is capable of routing the
flow of water in the necessary paths to regenerate
water treatment systems. The injector regulates the
flow of brine. The control valve regulates the flow
rates for backwashing, rinsing and the replenishing of
treated water into a regenerant tank.
The control valve uses no traditional fasteners (e.g.
screws); instead clips, threaded caps, nuts and snap
type latches are used. Caps and nuts only need to be
firmly hand tightened because radial seals are used.
Tools required to service the valve include one small
blade screw driver, one large blade screw driver,
pliers and a pair of hands. A plastic wrench is
available which eliminates the need for screwdrivers
and pliers. Disassembly for servicing takes much less
time than comparable products currently on the
market. Control valve installation is made easy
because the distributor tube can be cut 12.7mm (
1
/
2
“)
above to 12.7 mm (
1
/
2
“) below the top of tank thread.
The distributor tube is held in place by an o-ring seal
and the control valve also has a bayonet lock feature
for upper distributor baskets.
The AC adapter power pack comes with a 2.0 meter
power cord and is designed for use with the control
valve. The AC adapter power pack is for dry location
use only.
•
Solid state microprocessor with easy access
front panel settings.
•
Front panel display for time of day, volume
remaining, current flow rate and total volume
used (Totalizer).
•
Four methods to initiate regeneration; meter
immediate, meter delayed, time clock
delayed or pressure differential.
•
Optional double backwash feature offers
optimum regeneration cleaning ability and
efficiency.
•
Fully adjustable 6-cycle control delivers
controlled backwash, downflow brining/slow
rinse, second backwash, fast rinse, refill and
downflow service.
•
Downflow regeneration.
•
12-volt output AC Adapter provides safe and
easy installation.
•
Control valve design provides optimum
service and backwash rates.
•
Treated water regenerant refill.
•
Reliable and proven DC Drive.
•
General Factory set up is for M³
throughput regeneration with 2 AM
delayed regeneration and No second
Backwash.
Manual Initiated Regeneration
The user can initiate manual regeneration. The user
has the option to request the manual regeneration at
the delayed regeneration time of 2am or to have the
regeneration occur immediately:
1. Pressing and releasing immediately the
REGEN button. “
ƒ
” will flash towards regen
on the display and regeneration will occur at
2am the delayed regeneration time. The user
can cancel the request by pressing and
releasing the REGEN button.
2. Pressing and holding the REGEN button for
approximately 3 seconds will immediately
start the regeneration. The user cannot
cancel this request, except by resetting the
control by pressing NEXT and REGEN
buttons simultaneously for 3 seconds.
However this may totally clear all
the pre-programmed in functions
and is not recommended.
The WS1EI control valve consist of the following
components:
1. Drive Assembly
2. 2. Drive Cap Assembly, Main Piston and
Regenerant Piston.
3. Spacer Stack Assembly.
4. Injector Cap, Screen, Injector.
5. Refill Flow Control Assembly.
6. Drain Line Flow Control and Fitting Assembly.
7. Water Meter.
8. Bypass Valve.
9. Installation Fitting Assemblies.
Drive Assembly
The drive assembly consists of the following parts:
•
Drive Bracket.
•
Printed Circuit (PC) Board.
•
Motor
•
Drive Gears
•
Drive Gear Cover