background image

 

 

   

                                           

 

 

 

4

 

AMI210  User  Manual 

Care during use 

 

Do not walk on the power cord or allow anything to rest on it. 

 

Do not spill water or any other liquids on your system.   

 

When the system is turned off, a small amount of electrical current still flows. 

Always unplug all power, and network cables from the power outlets before 

cleaning the system. 

 

If you encounter the following technical problems with the product, unplug the 

power cord and contact a qualified service technician or your retailer.   

 

The power cord or plug is damaged. 

 

Liquid has been spilled into the system.   

 

The system does not function properly even if you follow the operating 

instructions.   

 

The system was dropped or the cabinet is damaged.   

 

Lithium-Ion Battery Warning

 

CAUTION

: Danger of explosion if battery is incorrectly replaced. Replace only with 

the same or equivalent type recommended by the manufacturer. Dispose of used 

batteries according to the manufacturer’s instructions. 

 

 

NO DISASSEMBLY 

The warranty does not apply to the products that have been disassembled by users 

 

WARNING 

HAZARDOUS MOVING PARTS 

KEEP FINGERS AND OTHER BODY PARTS AWAY 

 

 

 

Summary of Contents for AMI210






















































































Reviews: