![background image](http://html1.mh-extra.com/html/ibanez/tone-blaster-xtreme-tbx15/tone-blaster-xtreme-tbx15_owners-manual_604556012.webp)
ENGLISH
12
Names and function of each part
1. Cabinet
2. Speaker driver
3. Front corner
4. Bottom corner
5. Rear corner
6. Speaker grille
7. Handle
8. Chassis
9. Power cable
10. Metal Corner
11. INPUT jack
1/4" phone jack input.
12. OVERDRIVE switch
Operating this switch will make the LED light, and will switch the preamp to the
overdrive circuit, producing a natural-sounding overdrive effect. You can use the
GAIN control in conjunction with this to adjust the depth of distortion.
13. NORMAL/GAIN control
14. NORMAL/VOLUME control
15. CHANNEL switch
16. X MODE switch
This switches the preamp mode of the HOT channel.
17. X/HOT-GAIN control
18. X/HOT-VOLUME control
19. EQUALIZER/BASS/MIDDLE/TREBLE controls
BASS/MIDDLE/TREBLE controls
For the frequency response, refer to the spec sheet at the end of the manual.
20. REVERB/LEVEL control
This adjusts the level of the internal spring reverb.
21. CD input
This is a 1/4" stereo input jack. It is designed to be connected to the headphone
output of a portable CD or MP3 player, or similar device. Use a stereo 1/4" plug
cable to make connections.
Use the volume control of your portable CD player to adjust the volume. Please
be aware that this input jack is not suitable for use with a LINE OUT jack that is
not equipped with an adjustable volume control.
22. FOOTSWITCH jack
You can connect a separately sold IFS2X footswitch here, and use it to switch
channels or turn the reverb on/off.
23. HEADPHONE jack
This is a stereo 1/4" jack that outputs a monaural audio signal.
* If you're using headphones, no sound will be heard from the internal speaker.
Warning
The TBX series guitar amp's headphone output produces a large volume of
sound. Ensure that the volume has been turned down before beginning to play
using the headphones, and then slowly increase the volume until it has reached
the desired level. Note that the noise and distorted sound signals produced
when inserting or removing the plug at high volume levels will not only result in
damage to the headphones, it may also result in damage to the user’s hearing.
24. POWER switch
This turns the power on/off. When the power is on, the LED located above the
switch will light.
25. AC INPUT
26. SERIAL NO.
27. Cooling vent
28. SPEAKER OUTPUT jack
Use a speaker cable with a 1/4" plug to connect this jack to your speaker sys-
tem.
Use 8
Ω
or 4
Ω
speaker system(s). For the output ratings, refer to the specifica-
tions at the end of this manual.
*
Note:
Using speaker system(s) with an impedance below 4
Ω
will make the power
amp overheat, causing the protection circuit to operate so that the correct out-
put will not occur.
29. FUSE
30. FOOTSWITCH jack
Connect a separately sold IFS4X footswitch to this jack.
When connected as shown in the illustration, you can use the footswitch to
switch channels, turn the NORMAL channel's overdrive and the HOT channel's
boost on/off, and switch reverb on/off.
31. SEND output/RETURN input jacks
You can use these jacks to connect effect processors in an effect loop.
32. HUE control
This controls the overall brightness of the guitar sound.
Summary of Contents for Tone Blaster Xtreme TBX15
