Modello - Modèle - Model
Modell - Modelo - Model
ARMADIO PROFESSIONALE - SERVICE CABINET - ARMOIRE PROFESSIONNELLE
BERUFS KÜHLSCHRANK - ARMARIO PROFESIONAL - PROFESSIONELE KOELKAST
Fabbricante - Constructeur
Manufacturer - Hersteller
Fabricante - Fabrikant
EPTA S.p.A. - Sede legale
Via Mecenate, 86 - 20138 Milano – Italy
Capitale € 68.515.000 - R.E.A./MI – 1730229
Registro delle Imprese e Cod.Fiscale n. 04160730968
Partita IVA 04160730968
PAGE
15/64
N° DOC
UM000348
10. PUTTING INTO OPERATION
If the cabinet has been sharply tilted while being sited or for mounting of accessories, it must be left to stand
for at least three hours before being started to allow the lubricating oil to settle in the compressor.
Failure to do so can cause total destruction of the compressor refrigerating system.
Check that the voltage on the identification plate is the same as that of the network.
THE ELECTRICAL SUPPLY LINE TO WHICH THE REFRIGERATOR WILL HAVE TO BE
CONNECTED IS TO BE PROTECTED BY A VERY SENSITIVE DIFFERENTIAL
SWITCH (Rc=16A,Dc=30mA); IT IS ALSO TO BE LINKED TO THE
GENERAL EARTHING PLANT.
Earthing is necessary and compulsory by law.
Absolutely never use reduction units, patch cords, adapters or multiple socket
outlets to connect the counter. DIRECTLY connect the equipment to the mains.
The cable should be fully extended and located where it is unilikely to be struck, caught or stepped
on, away from water and the other liquids and heat sources and must not be damaged.
In case of breakage of the power cable
of the cabinet, it must be replaced by the manufacturer or by instruction it change of it.
Follow the manufacturer’s instructions to install the unit, using qualified personnel and complying with the
electrical regulations for the specific country.
Incorrect installation may cause injury and damage; the manufacturer is not liable for this.
The manufacturer disclaims all responsability for any damage to people or things due to
incorrect observance of this rule.
11. ENERGY SAVING TIPS
• Install the appliance in a dry, well-ventilated room away from heat sources (radiator, cooking surface and so on) and in a
position out of direct sunlight.
•
Follow the installation instructions to ensure adequate ventilation. Insufficient ventilation to the back of the appliance
causes an increase in energy consumption and reduces cooling efficiency.
• The internal temperature of the appliance depends on the room temperature, how often the doors are opened and where
the appliance is placed. These factors have to be taken into account when setting the thermostat. Only open the doors
when strictly necessary.
• Let hot food and drink cool down before placing them in the appliance.
•
The positioning of the shelves in the fridge has no effect on energy efficiency.
12. MAINTENANCE
WARNING!
Maintenance must be carried out by technical staff trained and enabled for intervention
on the flammable refrigerants.
WARNING!
Any work carried out on the appliance by the user strictly requires the power plug being
disconnected from the mains socket.
ATTENTION!
Use protective shoes and gloves during maintenance operations.
OPERATION
FREQUENCY
MAINTENANCE
AUTHORISED STAFF
Cleaning the outer surface
Based on use
Ordinary
User
Cleaning the accessible inner parts (do not use tools)
Based on use
Ordinary
User
Checking the power supply, electrical plugs and/or sockets
Six-monthly
Ordinary
User
Seals intactness check
Six-monthly
Ordinary
User
Check the acceptable condition of warning plates
Six-monthly
Ordinary
User
Condenser cleaning
Based on use
Ordinary
User
Fridge system tubing intactness check
Six-monthly
Ordinary
Technical support
Inspecting the cables and inner power connections
Six-monthly
Ordinary
Technical support
Replacing the power supply cable
-
Extraordinary
Technical support
Control panel replacement
-
Extraordinary
Technical support
Any other maintenance operation not planned in the previous points should be carried out by the
support centres authorised by our dealers or by qualified staff.
