ROBO Cylinder RCP4W Actuator Slider
Dust-proof/Splash-proof Type
First Step Guide First Edition
Thank you for purchasing our product.
Make sure to read the Safety Guide and detailed Instruction Manual (DVD) included with the product in addition to
this First Step Guide to ensure correct use.
This Instruction Manual is original.
•
Using or copying all or part of this Instruction Manual without permission is prohibited.
•
The company names, names of products and trademarks of each company shown in the sentences are registered
trademarks.
Product Check
The standard configuration of this product is comprised of the following parts
.
If you find any fault or missing
parts, contact your local IAI distributor.
1. Parts
No. Part
Name
Model
Quantity
Remarks
1 Main
Body
Refer to “How to read the model
plate”, “How to read the model No.”
1
Accessories
2
Motor • Encoder Cable
(Note 1)
1
3
First Step Guide
1
4 Instruction
Manual
(DVD)
1
5 Safety
Guide
1
Note 1 Please refer to [Wiring] for the applicable cables.
2. How to read the model plate
3. How to read the model No.
Note 1 Identification for IAI use only : It may be displayed for IAI use. It is not a code to show the model
type.
Caution in Handling
1. Handling of Robot
Pay attention to the followings when carrying an actuator by itself.
(1) Handling of the Packed Product
•
Do not damage or drop. The package is not applied with any special treatment that enables it to resist an
impact caused by a drop or crash.
•
An operator should never attempt to carry a heavy package on their own. Also, use an appropriate way for
transportation.
•
If the shipping box is to be left standing, it should be in a horizontal position. Follow the instruction if there is
any for the packaging condition.
•
Do not step or sit on the package.
•
Do not put any load that may cause a deformation or breakage of the package.
(2) Handling after Unpackaged
•
Do not carry the actuator by holding the cable, or do not move it by pulling the cable.
•
Hold the body base when transporting the actuator.
•
Do not hit or drop the product while carrying.
•
Do not give any excessive force to any of the sections in the actuator.
2. Handling of Multi-Axes Type
This is the case that this product is delivered with other actuators being combined. Multi-axes type will be
delivered in a package with an outer case fixed to a wooden base. Tables are fixed so they would not accidently
move while in transportation. The end of the actuator is also fixed to avoid it swinging by external vibration.
(1) Handling of the Packed Product
•
Do not damage or drop. The package is not applied with any special treatment that enables it to resist an
impact caused by a drop or crash.
•
An operator should never attempt to carry a heavy package on their own. Also, use an appropriate way for
transportation.
•
When suspending the package using ropes, pass the ropes from underneath the reinforcement frames at
the bottom of the base. When lifting with a forklift, also place the forks underneath the base.
•
Do not apply an impact on the package or let it bounce when putting it down.
•
Do not step or sit on the package.
•
Do not put any load that may cause a deformation or breakage of the package.
(2) Handling after Unpackaged
•
Secure the tables to prevent sudden movement during transport.
•
Appropriately fix the tip of the actuators if it is overhanging so it would not widely shake with external
vibration. If the actuator assembly is transported without the ends being secured, do not apply an impact of
0.3G or more.
•
In the case that the actuator needs to be carried up with ropes or another method, be sure to use an
appropriate cushioning to avoid the robot being deformed or put on an excessive pressure. And also, be
sure to keep the robot in a stable and horizontal posture. Make a tool to utilize the attachment holes and
tapped holes on the actuator and attach it if necessary.
•
Do not attempt to apply load to the actuator or connector box. Also, avoid the cables being pinched or
caused an excessive deformation.
3. Handling of Robot Mounted on Mechanical Equipment (System)
Followings are the cautions for when transporting the actuators installed in the machinery equipment (system) in
the whole system.
•
Affix the table so they would not move while transporting.
•
If any end of the actuator is overhanging, secure it properly to avoid significant movement due to external
vibration. If the actuator assembly is transported without the ends being secured, do not apply an impact of
0.3G or more.
•
Do not attempt to apply load to actuators or connector box when hanging the machinery equipment
(system) with tools such as a rope. Also, avoid the cables being pinched or caused an excessive
deformation.
Installation and Storage • Preservation Environment
1. Installation Environment
Do not use this product in the following environment.
Also make sure to keep enough work space necessary for maintenance.
•
Location exposed to radiant heat from a huge heat source such as the heat treatment
•
Location where the surrounding air temperature exceeds the range of 0 to 40
°
C
•
Location where condensation occurs due to abrupt temperature changes
•
Location where relative humidity exceeds 85%RH
•
The product gains the water-proof performance of IP65 protection structure if an air purge is conducted.
•
Location exposed to direct sunlight
•
Location exposed to corrosive gases or combustible gases
•
Location exposed to significant amount of dust, salt or iron powder (Outside of ordinary assembly plant)
•
Location where oil (includes oil mist and cutting fluid) or chemical is splashed
•
Location where the product main body receives vibration or hit impact
When using the product in any of the locations specified below, provide a sufficient shield.
•
Place subject to electrostatic noise
•
Location where exposed to the influence of strong electric or magnetic field
•
Location where exposed to the influence of ultraviolet or radiant rays
2. Storage • Preservation Environment
The storage and preservation environment should comply with the same standards as those for the installation
environment. In particular, when the machine is to be stored for a long time, pay close attention to environmental
conditions so that no dew condensation forms.
Unless specially specified, moisture absorbency protection is not included in the package when the machine is
delivered. In the case that the machine is to be stored and preserved in an environment where dew condensation
is anticipated, take the condensation preventive measures from outside of the entire package, or directly after
opening the package.
For storage and preservation temperature, the machine withstands temperatures up to 60
°
C for a short time, but
in the case of the storage and preservation period of 1 month or more, control the temperature to 50
°
C or less.
Storage and preservation should be performed in the horizontal condition. In the case it is stored in the packaged
condition, follow the posture instruction if any displayed on the package.
Names of the Parts
1. Standard
Type
Bracket (Front)
Base
Table
Bracket (Rear)
Motor Cover
Cable
Air Inlet
φ
6 for Air Purge
Bolt Cover (Front)
Side Cover
Front Cover
Grommet
Right
Left
Opening (with seal)
Bolt Cover (Rear)
Please refer to the Catalog or the Instruction Manual (DVD) for the dimensions and profile.
2. Wall-hang Type
Bolt Cover (Front)
Bolt Cover (Rear)
Right
Left
Bracket (Front)
Bracket (Rear)
Opening (with seal)
Please refer to the Catalog or the Instruction Manual (DVD) for the dimensions and profile.
3. Ceiling Type
Bolt Cover (Front)
Bolt Cover (Rear)
Right
Left
Bracket (Front)
Bracket (Rear)
Opening (with seal)
Please refer to the Catalog or the Instruction Manual (DVD) for the dimensions and profile.
Warning : Operation of this equipment requires detailed installation and operation instructions which are
provided on the DVD Manual included in the box this device was packaged in. It should be retained
with this device at all times.
A hardcopy of the Manual can be requested by contacting your nearest IAI Sales Office listed at
the back cover of the Instruction Manual or on the First Step Guide.
Model
Serial number
MODEL RCP4W-SA5C-I-35P-10-500-P3-M-A1
SERIAL No.000061911
MADE IN JAPAN
R C P 4 W - S A 5 C - I - 3 5 P - 1 0 - 5 0 0 - P 3 - M - A 1 - * *
Series
<Type>
SA5C, SA6C
SA7C
<Encoder Type>
I : Incremental
<Motor Type>
35P : 35
□
42P : 42
□
56P : 56
□
<Lead>
5
:
5mm
6
:
6mm
8
:
8mm
10 : 10mm
12 : 12mm
16 : 16mm
Identification for IAI use only
Note 1
<Option>
A1 : Cable exit to the left side
A3 : Cable exit to the right side
GE : Food grease indicated
NM : Reversed home specification
TFL : Wall mount to the left type
TFR : Wall mount to the right type
HFL : Ceiling mount to the left type
HFR : Ceiling mount to the right type
<Cable Length>
N :
No
cable
P :
1m
S :
3m
M :
5m
X
□□
:
Specified
length
R
□□
:
Robot
Cable
<Applicable Controller>
P3 : PCON-CA
<Stroke>
