background image

Version 1.0

5

13) Lightning

For added protection for this product during a lightning storm, or when it is left unattended and 

unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable 

system. This will prevent possible damage to the product due to lightning and power-line surges.

14) Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other 

electric light or power circuits, or where it can fall into such power lines or circuits. When installing 

an outside antenna system, extreme care should be taken to avoid contact with such power lines or 

circuits, as contact with them might be fatal.

15) Earthing the product

This product must be earthed properly to comply with the safety regulations in the country of use. 

If you are unsure of these regulations, please consult a qualified electrician.

16) Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to 

dangerous voltages or other hazards. Refer all servicing to qualified service personnel. If the Set 

does not operate properly, switch it off and call your dealer.

17) Damage Requiring Service

Isolate this product from the mains supply and refer servicing to qualified service personnel under 

the following conditions:

1. If the power-supply cord or plug is damaged.

2. If the glass front has been damaged.

3. If there is ingress of water between the glass and the LCD screen.

4. If the product does not operate normally by following the operating instructions. Adjust only

those controls that are covered by the operating instructions as an improper adjustment of other

controls may result in damage and will often require extensive work by a qualified technician to

restore the product to its normal operation. 

5. If the product has been dropped or the cabinet has been damaged.

6. If the product exhibits a distinct change in performance.

18) Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform 

safety checks to determine that the product is in proper operating condition and the front seal is 

intact.

19) Mounting

The product should be mounted on a wall only as recommended in the instructions. 

20) Power

This set operates on an AC supply; the voltage is as indicated on the label on the Manual. This 

appliance must be earthed at all times through the chassis as well as through the power lead. 

21) Location

Do not install on an unstable location with support area smaller than the DID SET.

Please secure enough space for safety use.

Summary of Contents for E 1086 T10 4K






























Reviews: