ADD CAMERA TO SRX-Pro PRO SETUP v7
1.
Launch the SRX-Pro Setup from the Desktop or from the SRX-Pro Monitor.
2.
In the IE browser, click
Continue to this website.
3.
Enter
your administrator
Username
and
Password
and click
LOGIN
4.
Click on the
Add
tile.
5.
If using SRX-Pro v.7.1, find your M79 camera in the list of
UNASSIGNED CAMERAS. You may need to click
REFRESH
.
If using SRX-Pro v.7.2 and above, click
SEARCH
and wait until your M79 camera is discovered.
6.
Select one or more M79 cameras with the same
login credentials and click
LOGIN
7.
Enter camera’s
Username
and the
Password
(configured in the previous
section) and click
SAVE
Login status for your device must now show the green check mark
.
Note: Devices with “Login failed” status will not be added.
8.
Click
ADD
. Your IP devices have been added to i3 SRX-Pro
Setup and are recording based on Motion schedule.
Change resolution and frame rate for each camera in the
List
section of the
i3 SRX-Pro Setup.
CHANGE CAMERA MODE
M79 Fisheye camera supports two display modes:
• Mode 1 (default): F Pa 3x ePTZ
• Mode 2: F 4x ePTZ
Switching to Mode 2 (optional):
1.
In the camera’s web interface,
click on the
Config
>
Fisheye Parameters
option.
2.
Click on the
Stream Mode
drop-down and select “Fisheye or 4 PTZ”
3.
Click
Save
, then click
OK
in the confirmation window. The camera will reboot.
CHANGE COMPRESSION
M79 is shipped pre-set to h.265 codec, which requires
SRX-Pro v7 and above. If using SRX-Pro v6,
you must change the compression to h.264 first.
1.
In the camera’s web interface,
click on the
Config
>
Video/Audio
option.
2.
Select “IP Channel 1” in
Channel ID
drop-down menu.
3.
Set compression to
H264
in
Video
drop-down menu for all streams and click
Save
. Click
OK
in the confirmation window.
4.
Repeat Steps 2-3 for IP Channels 2-5.
MOUNTING OPTIONS
Compatible Mounting Accessories:
B79 - back box for pendant installations
DB60 - goose-neck bracket
DB60CPM - corner/pole mount kit (use with DB60)
4.
Wait a few moments for a “Success” message in the Result field.
5.
Repeat Steps 1-3 for all detected M79 cameras in the ACT until each
camera has a
unique
IP address.
6.
To confirm your camera’s new IP address, click the IE icon
in ACT.
In the IE browser, enter administrative Username (i3admin) and (new) Password
and click
LOGIN
. The camera web interface will be displayed in the Internet
Explorer window. Download and run the plug-in, if prompted.
If you are unable to see live video on the screen, call i3 International technical
support team for troubleshooting tips: 1.877.877.7241
M79 6MP IP Fisheye Camera
QUICK START GUIDE
3.
Drill the conduit hole for the camera cable, if routing the cable upwards, and cover
the cable exit hole with the rubber plug (
E
). (If routing the cable sideways, through the
cable exit opening, do not drill the conduit hole.)
4.
Lift the magnetic cover ring off of the camera using the small notch (Fig. 4).
5.
Feed the camera cable through the cut conduit hole or through the side cable opening.
6.
Use the tapping screws to secure the camera to the prepared mounting surface. (Fig. 5)
7.
Re-attach the magnetic cover ring. (Fig. 5)
Mounting Type
Accessories required
Wall mount (e.g. drywall); Surface mount (e.g. drop ceiling) None
Pendant Mount; Electrical Gang Box (round/hex/single)
B79
Horizontal Wall Mount
B79 + DB60
Pole Mount / Corner Mount
B79 + DB60 + DB60CPM
i3 INTERNATIONAL INC.
1.866.840.0004
www.i3international.com
Camera’s default IP address:
192.168.0.16
.
Camera’s default Subnet mask address:
255.255.255.0
.
Default User name:
i3admin
ACTIVATE CAMERA IN ACT
Figure 4. M79, Ring notch and removal
Figure 5. M79, Surface installation
Part#: B79 (with RP1)
IMPORTANT:
Before adding your camera to SRX-Pro, set the administrative password
and unique camera IP. Your camera will remain inactive and inaccessible until
administrative password is set.
Setting administrative password:
1.
Connect your Annexxus M79 camera to the Gigabit switch.
2.
Launch i3 Annexxus Configuration Tool (ACT) v.1.9 or higher.
Download and install the latest ACT installation and GiPi package from i3 website, if
needed: https://i3international.com/download
3.
In the model drop-down list, select
M79
.
Security status will say “inactive”.
4.
In the Global Camera Settings, click
Set Password
5.
In the Set password window, enter the new password in the
Password
and
Confirm
fields. Follow secure password guidelines. Click
OK
.
The new administrative password will be assigned to the camera and the
Security status will change to “active”.
SET CAMERA IP IN ACT
Note: Your i3 Server must have a valid IP address (not APIPA)
Set your camera’s unique IP address:
1.
In Annexxus Configuration Tool, select your M79 camera in the list.
2.
Uncheck “Default Account” and enter “
i3admin
” into Username field and the new
administrative password into the Password field.
3.
Enter the new IP address and Subnet Mask and click
Update
.
Or
