1. Attach the supplied mounting template to
the mounting surface.
2. Drill 3 holes, as marked on the template and
insert three supplied anchors into the holes.
3. Drill the conduit hole for the camera cable,
as marked on the template.
4. Use the provided security Torx key to
loosen three screws securing the dome
bubble housing to camera module. Do not
completely remove the screws from the
dome bubble.
5. Gently pull the dome bubble downwards
and set aside.
6. Feed the camera cable through the cut
conduit hole.
7. Use three tapping screws provided
to secure the camera to the prepared
mounting surface.
8. Lift the inner liner for easier lens
adjustment.
9. Adjust the lens angle by panning the
camera lens assembly and rotating the camera lens base. Do not over-rotate the
camera lens beyond the stop point to avoid damage to the camera.
Pan Adjustment:
Pan the lens base until satisfied with the field
of view. DO NOT over-rotate.
Horizontal Rotation:
Rotate camera lens assembly in the lens.
DO NOT over-rotate to prevent twisted,
disconnected, or broken internal cables/
components.
Tilt Adjustment:
Tilt the camera lens within the certain range
(20° - 90°) to your desired field of view.
Loosen the adjustment screws before tilting
and re-tighten to maintain selected position
when done.
3-axis Range Limitations:
Pan range : 360°
Rotate range : ±175°
Tilt range : 20°~90°
10. Once the desired view is achieved, replace
camera’s inner liner until it snaps back into
place.
11. Replace the camera dome bubble and re-tighten 3 silver screws securing the dome
bubble to the camera base.
Ax47R/Ax67R IP Dome Camera
QUICK START GUIDE
CONNECT CAMERA TO i3 SRX-PRO SERVER
1.
Close SRX-Pro Server software by pressing
Alt+Shift+Ctrl+F4
.
2.
Write down the IP address of the onboard NIC (LAN) (or of NIC1 if your SRX-Pro
Server has two onboard NIC cards).
3.
Connect your camera to i3 SRX-Pro Server (see diagram above).
4.
Turn on your Annexxus camera.
5.
It may be necessary to download and install AnnexxusConfigTool (ACT) from our
website (www.i3international.com). Follow the ACT installation instructions until
the application has been successfully installed on your SRX-Pro Server. For SRX-
Pro v3.3.3.69 and above ACT is already installed.
6.
Either double-click i3 Annexxus Configuration Tool icon on the desktop to launch
the ACT application or click the “ACT Config Tool” button on the IP Camera Tab
in SRX-Pro.
7.
ANNEXXUS Configuration Tool window will display a list of active network
cameras.
8.
Select the desired Annexxus camera in the list (left-click).
9.
In the
Device(s) Communication
area, enter the new IP Range (address) and
Subnet Mask of the camera. The new camera IP address must match the IP
range of your SRX-Pro LAN or NIC1 card (see Step 2).
E.g. If your SRX-Pro Server’s IP address is 192.138.10.122, change your
Annexxus camera’s IP address to 192.138.10.XXX.
Remember: Annexxus Cameras cannot share an IP address, each camera
requires its own unique IP address.
10.
Make sure the
Default Account
checkbox is checked off.
11.
Click
Update
. Then click
Yes
in the confirmation window.
12.
Wait a few moments for a successful confirmation message.
13.
Repeat Steps 9-13 for all detected Annexxus cameras in the ACT application
OR Select multiple cameras (Ctrl + left click) and enter IP range to assign IP
addresses sequentially to the selected cameras.
14.
Once the IP address of the Annexxus camera(s) has been changed, make sure
you can connect to the camera(s) through Internet Explorer:
a.
Launch Internet Explorer by double-clicking the IE icon next to the desired
camera in the ACT.
The password window should be displayed.
b.
Enter the default
camera User Name:
i3admin
and default
Password:
i3admin
c.
Annexxus camera interface will be displayed in the Internet Explorer
window. You should be able to see the camera image on the screen.
If you do not see the camera image on the screen, call i3 International tech
support for troubleshooting tips: 1.877.877.7241
15.
Make sure that the latest version of GiPi updater is installed on your SRX-Pro
Server. Once the latest GiPi updater has been installed, restart i3 SRX-Pro Server.
Please go to www.i3international.com/software-downloads to download the
most recent GiPi.
16.
Log In and go to the
Setup
->
IP Camera
tab.
17.
Click the
Search
button to display connected Annexxus cameras.
18.
Select the detected camera in the list and click
Select
.
19.
In the
Select IP Camera window, enter the default camera User Name:
i3admin
and default Password:
i3admin
, then click
Add
.
20.
The selected camera will be added to the IP Camera list.
21.
Assign the IP camera to the SRX-Pro video channel in the
Ch. In.
column.
22.
Your Annexxus camera is now connected to SRX-Pro Server and is ready to
record. You may change resolution and frame rate for the Annexxus camera in
the IP Camera tab menu or you may choose to configure the camera’s advanced
settings.
Camera’s default IP:
192.0.0.16
. Default Login / PW:
i3admin
/
i3admin
i3 SRX-Pro Server
Crossover direct connection
LAN
i3 SRX-Pro Server
Via Gigabit Switch
Connection Type 1:
Connection Type 2:
INSTALLING THE CAMERA
Prepare the mounting surface.
Depending on the type of installation, additional mounting accessories may need to be
purchased. After installing the camera, your network camera must be accessible from your
local network (LAN).
•
It is the installer’s responsibility to ensure that the mounting surface is suitable for the
chosen installation method.
•
Based on installation location and surface type, supplied screws and anchors may not
be adequate. Mounting hardware is site-specific and may need to be supplied by the
installer.
QR Code to Complete
User Manual / ACT
CANADA
780 Birchmount Road,
Unit 16, Toronto,
ON, M1K 5H4
U.S.A
4450 Witmer Industrial Estates
Unit 4 Niagara Falls,
NY 14305
www.i3international.com
1.866.840.0004
