User Manual
i3-TRNG-CAMS-
Am42R-UM
.indd
Rev.
161123
HD720P (1MP) Vandal-Proof Infrared Dome Camera
Am42 Series
The
Am42 indoor/outdoor series cameras include the Am42R and the Am42RB.
•
Am42R comes in white.
•
Am42RB comes in black.
SAFETY
When installing your Am42 Series camera be sure to avoid:
• excessive heat, such as direct sunlight or heating appliances
• contaminants such as dust and smoke
• strong magnetic fields
• moisture and humidity
• areas with mechanical vibrations
• fluorescent lamps or objects that reflect light and unstable light sources
• temperatures below -30° C (-22° F) and above 60° C (140° F)
.
• To avoid electrical shock and to preserve the product warranty, DO NOT disassemble
the camera. Refer servicing to qualified personnel only.
POWER SUPPLY
Ensure the supplied voltage meets the power consumption requirements of this camera
before powering the camera on. Incorrect voltage may cause irreparable damage to the
video camera and will effectively void the camera warranty.
This camera series accepts DC 12V and AC 24V power.
CLEANING
• For maximum optical clarity, the camera dome or lens must remain clean. Use a soft,
dry cloth to remove finger prints or dust from the dome cover.
• Use a blower to remove dust from the lens.
• Do not use volatile solvents such as alcohol, benzene, or thinners, as they may
damage the surface finishes.
PACKAGE CONTENTS
In addition to this manual and a fully assembled camera, the product box includes:
1. Security Torx bit x1
2. Plastic Anchor x4
3. Round Head Screw (Tapping Type) x4
4. Spot monitor auxiliary video output
cable x1
5. Surface Mount template x1
1.
3-axis camera module / second housing.
2.
Long screws (pre-installed) for attaching camera module to the back box, x3
3.
Lens.
4.
IR board.
5.
Lens focus adjustment w/ locking screw (Far / Near).
6.
Lens zoom adjustment w/ locking screw (Tele / Wide).
7.
Joystick (for on-screen camera menu control).
8.
Dip switch (CVBS / TVI output). Remove the Shroud/Liner for easy access.
9.
2-pin Service (spot) monitor output.
10.
Power connector (12DC / 24AC).
11.
TVI High-definition analog video connector (1MP. 1280x720 = 720P).
To use high-definition analog stream (1MP), the camera must be connected to
i3’s HR16 encoder or standalone Veo17 DVR. Put the Dip switch (#7) into the “TVI”
position to enable TVI video stream.
12.
CVBS standard-format analog video connector (4CIF = 720x480). Can be
connected directly to the BNC board on the i3’s HVR units. Put the Dip switch (#7)
into the “CVBS” position to enable composite video stream.
13.
Lexan Bubble (Dome).
14.
Inner liner / Shroud (Removable for convenient lens position adjustments).
15.
Screws attaching camera bubble to the camera module (x3 silver).
16.
Camera’s back box. Compatible with i3’s DB60/DB60B Goose-neck bracket. Can
also be used for pendant mount installations.
17.
Side conduit hole (3/4”).
Remove plug to route power and video cables through the side opening.
Use the plug for the top conduit hole in that scenario.
When using outdoors, sealant must be used to maintain the IP66 status.
18.
Top conduit hole (3/4”). Can also be used for pendant mount installations.
When using outdoors, sealant must be used to maintain the IP66 status.
19.
Mounting holes, partially drilled, x6 (complete drilling the holes prior to
installation).
CAMERA PARTS AND DEFINITIONS
1
3
5
6
10
11
12
7
8
9
CVBS
TVI
13
15
16
19
17
18
14
1MP
720x480
4
4
1
2
3
5
Lens Direction
GUIDE PATTERN
HIGH-DEFINITION ANALOG VIDEO SUPPORT
Your Am42 series camera supports both the standard composite analog video stream
(720x480) and a HD-TVI - high-definition TVI video stream (1MP).
Only
one
type of video stream may be used at-a-time.
To use the camera’s HD-TVI stream (1MP), the user must set the on-board dipswitch to TVI
mode and then connect the camera’s gray BNC cable connector (labeled 1MP) to i3’s HR16
video encoder or standalone Veo17 DVR.
Important:
HD-TVI stream will NOT be supported if the camera is connected directly to
i3’s HVR unit. When connecting to i3 DVMS directly, set the on-board dipswitch to CVBS
mode and connect the camera’s black BNC cable connector (labeled 720x480) to the
DVMS’ BNC board or BNC fly-out cable.
UP
2
2
