SAFETY
When installing your Ax47DC camera be sure to avoid:
•
excessive heat, such as direct sunlight or heating appliances
•
contaminants such as dust and smoke
•
strong magnetic fields
•
sources of powerful electromagnetic radiation such as radios or TV transmitters
•
moisture and humidity
•
areas with mechanical vibrations
•
fluorescent lamps or objects that reflect light
•
unstable light sources as this may cause flickering
•
temperatures below -10° Celsius or 14° Fahrenheit and above 50° Celsius or 122°
Fahrenheit
POWER SUPPLY
Ensure the supplied voltage meets the power consumption requirements of this camera before
powering the camera on. Incorrect voltage may cause irreparable damage to the video camera
and will effectively void the camera warranty. PoE power is supported by this camera series. To
mount the camera, do the following:
CLEANING
•
For maximum optical clarity, the camera dome or lens must remain clean. Use a soft, dry
cloth to remove finger prints or dust from the dome cover.
•
Use a blower to remove dust from the lens.
•
Clean the body with a soft, dry cloth. If it is very dirty, use a cloth dampened with a small
quantity of neutral detergent, then wipe dry.
•
Do not use volatile solvents such as alcohol, benzene, or thinners, as they may damage
the surface finishes.
SERVICING
To avoid electrical shock and to preserve the product warranty, DO NOT disassemble the
camera. Refer servicing to qualified personnel only.
PACKAGE CONTENTS
1.
Mounting guide pattern sticker x1
2.
Torx key x1
3.
Plastic anchor x3
4.
Round head screw (tapping type) x3
5.
CAT5 camera cable x1
CAMERA PARTS AND DEFINITIONS
Quick Start Guide
1.3MP Network Door Counting Dome Camera
Ax47DC
i3-TRNG-CAMS-
Ax47DC-QuickGuide
.indd
Rev.
170323
1
Ceiling Mounting
Hole
Hole
Hole
Hole
110.97 mm
82 mm
50.5 mm
1
1
1
3
4
2
6
7
8
9
5
1.
Mounting holes (x3)
2.
Dome bubble housing / Dome cover
3.
Screws securing the dome bubble housing to camera module (x3, silver)
4.
Lexan bubble
5.
Screws attaching camera module to the camera base (x4, black)
6.
Lens base. Rotate to adjust lens angle.
7.
Camera Lens Assembly. Pan to adjust lens angle.
8.
Tilt bracket with two locking screws. Loosen the screws and tilt to adjust
lens angle.
9.
Inner Liner / Shroud. Attach the dessicant to the inside of the Inner Liner,
without obstructing the lens movement.
10.
Camera lens.
11.
RJ45 Ethernet PoE Port with waterproof RJ45 connector assembly.
Insert an Ethernet cable into the port for network connection as well as
PoE (Power over Ethernet) capability. To maintain water-resistant rating
in outdoor installations, make sure to use the included waterproof RJ45
Connector assembly.
12.
Reset/Default button. Press for 1 second to reboot the camera. Press for 6
seconds to restore camera settings to factory defaults.
13.
MicroSD Card slot for on-camera video storage. (MicroSD card sold
separately).
12
11
13
2
3
4
5
Scan this QR code or visit
www.i3international.com
to view and
download the full User Manual for this camera. Also available for
download is the
AnnexxusConfigurationTool
or ACT program used
to locate and configure your cameras with your SRX-Pro software.
This program is already installed in SRX-Pro v3.3.3.69 and higher.
Please contact our Technical Support team if you have any questions or
concerns regarding camera installation or you require software services
or support. Technical support can be reached by email at:
or by phone toll free
1.877.877.7241.
QR Code to Complete
User Manual / ACT
10
