background image

Page 

3

 of 

20

 

Moving Head Controller 2.0 Manual Rev2 

1.

 

B

EFORE

 Y

OU

 B

EGIN

 

What Is 

Included 

· 1x Moving Head Controller V2.0

 

· 2x Mounting Brackets 

 

· 1x External Power Supply

 

· 1x A-B USB Cable

 

 

 

 

 

 

 

 

 

Unpacking 

Instructions 

 

Carefully unpack the 

Moving Head Controller 2.0

 

and check that all the parts are in the 

package, and are in good condition. 

Claims 

If the box, or any of the contents, appear damaged from shipping, save all the packaging and 
file a claim with the carrier immediately. Failure to report damage to the carrier immediately, 
or failure to save all the packaging, can invalidate a claim. 
For other issues, such as missing components or parts, damage not related to shipping, or 
concealed damage, file a claim with JPC Lighting within 7 days of delivery.  
 

Conventions 

Convention 

Meaning 

1

512 

A range of values 

50 to 60 

A set of values 

15

 

Information shown on the display 

Settings 

A menu option 

Menu > Settings 

A sequence of menu options 

<Enter> 

A button 

 

Symbols 

Convention 

Meaning 

 

Critical information. Ignoring it can cause malfunction, damage the 
product, or harm the operator. 

 

Important information. Ignoring it can cause the product to 
malfunction. 

 

Useful information. 

 

 

Disclaimer 

 
The information and specifications contained in this User Manual are subject to change 
without notice. I2R Tech Lighting Solutions® assumes no responsibility or liability for any 
errors or omissions and reserves the right to revise or recreate this manual at any time.  

© Copyright 2020 I2R Lighting Solutions®. All rights reserved. 

 

 

 

 

Summary of Contents for Moving Head Controller 2.0





















Reviews: