background image

19” Full IP67 Rugged PC User’s Manual

 

2

If any of the following situations arises, get the equipment checked by service personnel:

 

The power cord or plug is damaged.

 

Liquid has penetrated into the equipment.

 

The equipment has been exposed to moisture.

 

The equipment does not work well, or you cannot get it to work according to the  user’s manual.

 

The equipment has been dropped and damaged.

 

The equipment has obvious signs of breakage.

Do not leave this equipment in an uncontrolled environment where the storage temperature is below
-10°C (14°F) or above 60°C (140°F). It may damage the equipment.

CAUTION 

– Use recommended mounting apparatus to avoid risk of injury.

WARNING 

– Only use the connection cords which comes along with the product, when in

doubt, please contact the manufacturer.

Provision shall be made to provide transient protection device to be set at a  level not exceeding 140%
of the rated voltage at the power supply terminals of  the apparatus.

WARNING 

– The equipment should be adequately protected from direct light when installed indoor

or outdoor.

Summary of Contents for IP67 Aluminum


























Reviews: