background image

7

We shall not be liable for content 
compensation, losses of recorded or 
edited content and any direct or indirect 
consequent damages caused by failure to 
record or edit due to faults with this unit or 
the microSD memory card. In addition, the 
same provisions apply after unit is reparied.

About the CMOS image sensor

•  When continuously shooting a bright 

light source such as a spotlight, the color 
filter of the CMOS image sensor may 
become deteriorated and this may cause 
discoloration. Even when changing the 
fixed shooting direction after continuously 
shooting a spotlight for a certain period, the 
discoloration may remain. 

• 

When shooting fast-moving subjects or 
objects crossing the shooting area may look 

to be bending askew.

Cleaning this product body

Be sure to turn off the power before cleaning. 

Failure to observe this may cause injury. 

 

Do not use benzine, thinner, alcohol, or any other 
types of solvents or detergents. Otherwise, it may 
cause discoloration. When using a chemical cloth 
for cleaning, read the caution provided with the 
chemical cloth product.

•   Do not loozen or remove screws unless 

instructed to do so in the product 
documentation.

Cleaning the lens

Use a lens cleaning paper (used to clean camera 
lenses or lenses of spectacles). When using 
solvent, use an alcohols solvent and do not use a 
glass cleaner or a thinner.

<WV-S25500-V3LN><WV-S25500-V3LN1> 
<WV-S25600-V2LN><WV-S25700-V2LN> 
Cleaning of the dome cover

•  When cleaning the dome cover, hose or spray 

fresh water that is not containing lubricant 
agent or silicon substances and wash away 
adherents such as grain of sand. If dirt is hard 
to remove, use a sponge soaked into the 
fresh water mentioned above and wipe off.

•  Do not wipe the dome cover with a dry cloth. 

(Using dry cloth may spread oil constituent 
adhered to the surface, and it may result in 
damaging the ClearSight coating.)

•  If dirt cannot be wiped off with a damp cloth, 

use a neutral detergent for kitchen utensils, 
and sufficiently rinse off the detergent. 
When using a detergent containing wax 
components such as determent for washing 
cars, a detergent with polishing material such 
as a compound, etc., and a non-neutral 
(weakly acidic or weakly alkaline) detergent, 
it can decrease the hydrophilic property and 
peel off the surface coating.

•  Do not use organic solvent such as benzine 

and thinner.

•  Before using a spray, abandon a few sprays 

to eliminate impurities.

•  The mark of light-shielding parts left inside 

the dome cover or dirt on the dome cover 
may influence the reflection of infrared rays. 
Therefore, likewise remove those marks and 
dirt using cleaning paper.

•  Improper cleaning of the dome cover may 

cause the ClearSight coating to become 
less effective. In this case, in order to have 
effective ClearSight coating, a new dome 
cover must be purchased to replace the 
existing dome cover. Consult with your dealer 
or construction contractor.

<WV-S25700-V2L><WV-S25700-V2LG> 
<WV-S25600-V2L><WV-S25600-V2LG>

 

<WV-S25500-V3L><WV-S25500-V3LG> 
<WV-S25500-F6L><WV-S25500-F3L>

 

Cleaning of the dome cover 

Use lens cleaning paper (used to clean camera 
or spectacles lenses) to remove any dirt on the 
dome cover. (If dust or the like is adhered at this 
time, the dome cover may get scratched. We 
recommend rinsing for stubborn stains.) The mark 
of light-shielding parts left inside the dome or dirt 
on the dome cover may influence the reflection 
of infrared rays. Therefore, likewise remove those 
marks and dirt using cleaning paper.

About the ClearSight coating

Due to effectiveness of the ClearSight coating, 
drops are likely to be accumulated right under the 
camera and it may cause a partial distortion of the 
video.

Summary of Contents for WV-S25700-V2L





























Reviews: