2
Important Safety Information
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT
CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your
safety and convenience.
A 5 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the replacement
fuse has a rating of 5 amp and that it is approved by ASTA or BSI to
BS1362.
Check for the ASTA mark
or the BSI mark
on the body of the
fuse.
If the plug contains a removable fuse cover you must ensure that it is
refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a replacement
cover is obtained.
A replacement fuse cover can be purchased from your local our dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE
SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE
REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT
OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET.
How to replace the fuse
The location of the differs according to the type of AC mains plug (fig-
ures A and B).
Confirm the AC mains plug fitted and follow the instructions below.
Illustrations may differ from actual AC mains plug.
Open the fuse cover with a screwdriver and replace the fuse and close
or attach the fuse cover.
Figure A
Figure B
For U.K.
Caution:
• This recorder is only intended for a connection to an ethernet
or PoE network without routing to the outside plant.
• Be sure to install disconnect devices such as a circuit breaker
to shut down the main power of power supplying equipment
to this product.
• The socket-outlet shall be easily accessible.
• Before attempting to connect or operate this product, please
read these instructions carefully.
Notice:
• This product is not suitable for use in locations where children
are likely to be present.
• For information about screws and other parts required for
installation, refer to the corresponding section of this
document.
• The power supply cord is used as the main disconnect
device, ensure that the socket-outlet is located/installed near
the equipment and is easily accessible.
• This product is a professional equipment.
: Functional earthing; functional grounding(US) symbol
: Direct current symbol
: Alternation current symbol
: Polarity of d.c. power connector
: For indoor use only
: Computer network
: Mouse port
: USB port
: "ON"/"OFF" (push-push)
The model number and serial number of this product may
be found on the surface of the unit.
You should note the model number and serial number of
this unit in the space provided and retain this book as a
permanent record of your purchase to aid identification in
the event of theft.
Model No.
Serial No.
For U.S.A.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired operation.
For U.S.A.
Supplier's Declaration of Conformity
Trade Name: i-PRO
Model No. : WJ-NX310K
Responsible Party: i-PRO Americas Inc.
8550 Fallbrook Drive, Suite 200
Houston,
Texas 77064
Support Contact: 1-800-513-5417
For U.S.A.
Note:
This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
when the equipment is operated in a commercial
environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
FCC Caution:
Changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
For U.S.A.
CAN ICES-3(A)/NMB-3(A)
For Canada
WARNING:
• All work related to the installation and earthing of this product
should be made by qualified service personnel or system
installers.
• Operation of this product in a residential environment could
cause radio interference.
