![background image](http://html1.mh-extra.com/html/hyundai/h-sa6041/h-sa6041_instruction-manual_2195687002.webp)
HYUNDAI
H-SA6041
2
YOUR NEW HIGH FIDELITY BRIDGEABLE/STEREO AMPLIFIER IS DESIGNED TO DELIVER MAXIMUM ENJOYMENT AND ONE YEAR OF
TROUBLE FREE SERVICE.
Features
·
Four Class ''AB'' High-Current Dual Discrete Drive Stages.
·
Class ''AB'' Technology MOSFET PWM Power Supply.
·
Bridgeable & TRI-Mode Operation.
·
Continuously Variable 12dB/Octave High Pass & 12dB/Octave Low Pass Crossover.
·
Subwoofer Variable Crossover for Deep Bass Control.
·
Enhanced Bass Boost 0/+6/+12dB @50Hz
·
Silver Plated RCA & Power, Speaker Terminal.
·
Soft Start & Muting.
·
Overload, Thermal, Short Circuit Protection.
·
Power & Protection indicator.
Precautions: Read First!
·
If after reading the direction you feel uncomfortable about installing the amplifier in your car, or not equipped or competent to do so, you should have the
amplifier installed by an authorized installer. It's your car!
·
Negative battery terminal must be disconnected before any electrical connections are made.
·
Be sure choose a location that provides substantial ventilation for the amplifier.
·
The most preferred locations would be in your car's trunk, under the front seats or on the back wall of a truck.
·
The location chosen should provide at least 2" of clearance above the amplifier for adequate ventilation.
·
If the amplifier is to be mounted vertically be sure that it is in a place where adequate air will flow along the length of its heatsink fins for cooling.
·
NEVER mount the amplifier up side down, this will cause the heat to rise back into the amplifier causing thermal shutdown or possible permanent
damage.
·
NEVER mount the amplifier in a location that is subject to direct sunlight or exposed to moisture.
·
Be sure to mount the amplifier to a strong, solid surface which will not give way under the stress of a sudden stop or accident.
·
Make sure that the mounting screws will not penetrate the gas tank, brake and fuel lines, wiring or other critical parts of your car when installed.
·
NEVER operate the amplifier without the proper power and ground wire 10 gauge minimum.
·
NEVER operate the amplifier without proper fusing. Fuse holder must be located with in 0.5 meters from the battery. This fuse is to protect the car not
the electronics. In case of a short, the fuse will blow instead of the wire burning up. Using other than the recommended fuse ratings at the battery and at
the amplifier may cause damage to the amplifier and will void your warranty.
·
Do not run wiring underneath or outside the car since exposure to the elements may cause the insulation to deteriorate rapidly, resulting in short-circuits
and/or intermittent operation. All cables should be run beneath carpets and inside trim pieces.
·
To help minimize interference, it is best to run the power cables along the opposite side from the audio cables.
Summary of Contents for H-SA6041
