Hyundai 2007 Elantra Owner'S Manual Download Page 31 | Manualshive

Page: 31 / 339

background image

Safety system of your vehicle

12

3

Seat belt restraint system

Seat belt warning

Seat belt warning light

If the driver's seat belt is not fastened
when the ignition key is turned ON, the
seat belt warning light blinks for approxi-
mately 6 seconds. And if the vehicle
speed exceeds 10km/h with the seat belt
unfastened, the seat belt warning light
blinks with the pattern of 6 seconds on
and 24 seconds off for 11 times.The seat
belt warning light will stop if the seat belt
is fastened or the vehicle speed is
reduced to below 5km/h.

SEAT BELTS

1GQA2083

WARNING

• For maximum restraint system

protection, the seat belts must
always be used whenever the car
is moving.

• Seat belts are most effective

when seatbacks are in the
upright position.

• Children age 12 and younger

must always be properly
restrained in the rear seat. Never
allow children to ride in the front
passenger seat. If a child over 13
must be seated in the front seat,
he/she must be properly belted
and the seat should be moved as
far back as possible.

• Never wear the shoulder belt

under your arm or behind your
back. An improperly positioned
shoulder belt can cause serious
injuries in a crash. The shoulder
belt should be positioned midway
over your shoulder across your
collarbone.

(Continued)

(Continued)
• Avoid wearing twisted seat belts.

A twisted belt can't do its job as
well. In a collision, it could even
cut into you. Be sure the belt
webbing is straight and not twist-
ed.

• Be careful not to damage the belt

webbing or hardware. If the belt
webbing or hardware is dam-
aged, replace it.

«
...
29
30
31
32
33
...
»

Summary of Contents for 2007 Elantra




















































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 Elantra

Brand: Abarth Pages: 176

Brand: RAM Pages: 292

Brand: RAM Pages: 116

Brand: Prorack Pages: 14

Brand: PEUGEOT Pages: 249

Brand: UAZ Pages: 90

DELTA DL FIX 209FP

Brand: Menabo Pages: 8

Brand: Cadillac Pages: 529

Brand: Toro Pages: 16

Brand: Acura Pages: 7

Brand: Ford Pages: 2

MagicSafe MSG150

Brand: Waeco Pages: 20

Brand: Menabo Pages: 8

Brand: Subaru Pages: 2

Brand: Rhino-Rack Pages: 2

Brand: Husky Pages: 8

Brand: Painless Performance Pages: 16

Brand: EUFAB Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands