background image

4

Status Indication 

Status Icon

Name

Icon

Terminal Status

Battery 
Strength 
Icon

The battery strength is 
low.
More bars indicate more 
battery strength.

RSSI Icon

The terminal has not 
registered with the 
network (applicable for 
TMO only). 
More bars indicate a 
stronger signal. 

Message 
Icon

Unread message(s). 
The Inbox is full. 

Operation 
Mode Icon

The terminal is operating 
in TMO. 

The terminal is operating 
in DMO. 

The terminal is operating 
in fallback mode. 

Profile 
Icons

Silent 
Normal
Vibration

Accessory 
Icon 

The audio accessory is 
connected. 

Name

Icon

Terminal Status

GPS Icon

A GPS module is 
connected and the valid 
GPS data is received.
Valid GPS data can be 
received, and the audio 
accessory has been 
connected.
A GPS module is 
connected and no valid 
GPS data is received.
No valid GPS data can 
be received, and the 
audio accessory has 
been connected.

BT Icon 

The BT feature is 
enabled but the product 
is not connected to BT 
device. 
The product is 
connected to BT device. 

Call Icon 

A call is in progress.

Group 
Selection 
Icon

Select a talkgroup. 

Name

Icon

Terminal Status

Gateway 
Icon

A gateway device is 
available and connected 
in DMO. 

A gateway device 
is available but 
unconnected in DMO. 

Repeater 
Icon

A repeater is available 
and connected in DMO. 
A repeater is available 
but unconnected in 
DMO. 

LED Indicator

LED Indication

Terminal Status

Glows red

Transmitting 

Glows green

Receiving 

Flashes  green 
slowly

Channel free in TMO

F l a s h e s  b l u e 
slowly

Channel free in DMO

Glows orange.

Channel busy in DMO

Summary of Contents for TETRA Z1PF4


















Reviews: