manualshive.com logo in svg

HYT TM-610, Manual

Share
Download
HYT TM-610 Manual Download Page 17

第

   

页

 

共

 32 

页

 

17

Basic Operations 

Turn Radio On/Off 

Press the power switch to turn on the radio. 

Press and hold down the power switch for about 1 second to turn off the radio. 

 

Adjust the Volume 

Turn the Volume Control Knob clockwise to increase the volume, or counter-clockwise to 

decrease the volume. During adjusting, please note that if the radio is programmed with 

CTCSS/CDCSS or 2-Tone signalling squelch, noise will not be heard from local speaker 

even though you turn the volume control knob fully clockwise. 

 

Monitor 

If the Monitor function is set by your dealer, press the programmed Monitor key while in 

receive mode, to hear activities on the current channel. 

The Monitor key is programmable with one of the following four operating modes by your 

dealer: 

1. Carrier 

Squelch-Momentary 

Hold down the [MONI] key to open CTCSS/CDCSS/2-Tone signalling squelch. Release to 

close the signalling squelch. 

2. Carrier 

Squelch-Toggle 

Press the [MONI] key to open CTCSS/CDCSS/2-Tone signalling squelch. Press again to 

close the signalling squelch. 

3. Squelch 

Off-Momentary  

Hold down the [MONI] key to open carrier squelch; Release to close the carrier squelch. 

4. Squelch 

Off-Toggle  

Press the [MONI] key to open carrier squelch. Press again to close the carrier squelch. 

 

Select a Channel 

The [

▲

]/[

▼

], [P1]-[P4] function keys are programmable by your dealer to select a channel. 

Summary of Contents for TM-610

































Reviews:

No comments

Brands by name

Popular brands

Load more brands