background image

Vented

Sealed

ENCLOSURES

Woofer Cut-out: 

Mounting Depth: 

Sealed Box: 

Vented Box: 

   • Vent Area: 

   • Vent Length: 
   • Tuning:
Dynamic Power : 
Nominal Power : 

7.48 in.

(190 mm)

5.8 in.

(148 mm)

.76 cu. ft.

(21.52 L)

1.15 cu. ft.

(32.56 L)

16 in.

(6.2 cm)

 36Hz

1000 Watts

500 Watts

9.62 sq. in.

(62.06 cm2)

9.33 in.

(237mm)

6.24 in.

(158.50 mm)

1.44 cu. ft.

(40.77L)

1.66 cu.ft.

(47.00L)

16 in.

(6.2 cm)

 35Hz

2000 Watts

1000 Watts

12.57 sq in.

(81.09 cm2)

11.02in.

(280 mm)

6.88 in.

(175 mm)

1.60 cu. ft.

(45.30L)

1.75 cu. ft.

(49.55L)

15 in.

(5.9 cm)

 35Hz

2000 Watts

1000 Watts

12.57 sq in.

(81.09 cm2)

13.74 in.

(349 mm)

7.83in.

(199.50mm)

2.72 cu.ft.

(77.02L)

2.99 cu. ft.

(84.66L)

11 in.

(4.33 cm)

 35Hz

2000 Watts

1000 Watts

19.63 sq in.

(126.64 cm2)

Calculating External Volume

Calculating Internal Volume

To calculate box volume, measure the outside Width x Height x Depth of

the enclosure.  

Example 12” x 14” x 9”=1512 ÷ 1728” Cubic feet

Next you must convert cubic inches into cubic feet. To do this, you must

divide the cubic inches total by 1728”. 

Example 1512 ÷ 1728=.875 Cubic feet

To calculate the internal (net) volume of the above box you must first multiply

the thickness of the wood you are using by Two(2). 

Example 3/4” x 2= 1.5“

Next subtract 1.5 from each of the outside measurements of the box.

Width

Height

Depth

12 - 1.5 = 10.5                 14 - 1.5 = 12.5               9 - 1.5 = 7.5

Multiple the new totals

 (H x W x D)

 

Example: 10.5 x 12.5 x 7.5 = .5696

Next you must convert cubic inches into cubic feet.  To do this, you must

divide the cubic inch total by 1728”. 

Example 984.375 ÷ 1728=.5696 cubic feet.          

It is recommended to build your enclosure from at least 3/ 4” thick MDF (medium density fiber
board).  Make sure the enclosure is sealed airtight.

HWP8

HWP10

HWP12

HWP15

RECOMMENDED  ENCLOSURES

CALCULATING ENCLOSURES

Summary of Contents for HWP8









Reviews: