Hypertherm Powermax 1000 Training Download

Page: 48 / 55



Manually adjust the Z axis to about 1/16(0.0625)”- 1/8(0.1250)” above the stock



Use a penny (0.0598”) to gauge (– it should just drag when sliding between the stock &
the torch tip



Press the Z axis up or down arrow to adjust



For finer adjustments use the dial -- clockwise to raise & counter clockwise to lower



This height control overrides any auto-torch height



Select the parts to cut



Using the click & drag technique OR hold CTRL key & click each line



Notice the parts to be cut are highlighted in green as selected



To initiate the cut, use

Machine->Cut



“Dry run” the cuts

with the “Cutting” setting on the PlasmaCAM controller OFF



Once finished, turn everything off (including the evacuation fan) & remove the air hose from
the plasma cutter



Clean up, please

Bringing it all Together – Adjust Torch & Stock

Next: Other info

Summary of Contents for Powermax 1000
























































Search results

Summary of Contents for Powermax 1000

Reviews:

Related manuals for Powermax 1000

Brands by name

Popular brands

Hypertherm Powermax 1000, Training

Search results

Summary of Contents for Powermax 1000

Reviews:

Related manuals for Powermax 1000

Brands by name

Popular brands