background image

11

NOTE: 

The accessories of battery charger (HT19-401-003-13 /ACG318W1U) and battery pack (ABP118T7/

HT19-401-003-17 ) illustrated or described are not included in HT19-401-003-03 delivery.

OPERATION INSTRUCTIONS

Warning!

 The charger and battery pack are specially designed to work together so do not attempt 

to use any other devices. Never insert or allow metallic objects into your charger or battery pack con-

nections because of an electrical failure and hazard will occur.

1. Command feeding the line (See Fig. K)

Your trimmer is equipped with a Command Feed System. For efficiently feeding the line, just press the 
command feed button while the machine is running until you hear the ‘clattering’ noise of the line cutting.
The motor will shut off when pressing the Command Feed button and will restart when releasing the 
button. During that process the line will automatically feed additional line for cutting.

2. Manually feeding the line (See Fig. L)

Turn off the trimmer and remove the battery. If required, line can be fed out manually. To operate, press and 
release manual Line Feed Button, while gently pulling out the line until it is long enough to reach the Line 
Cutter. If the line extends past the Line Cutter, too much line has been fed out. If too much line is fed out, 
remove the Spool Cap and turn Spool counter-clockwise until the line is at the desired length.

3. Manually winding the line (See Fig. P, Q, R, S)

Take approximately 6m of line. Insert 2mm of line into the Spool holes and wind line in the direction of 
the arrows on the top of the Spool. Leave approximately 100mm of line unwound and place into the cleat. 
Ensure that the line is neatly coiled on the Spool. Failure to do so will impair the efficiency of the automatic 
line feed. Then fit the Spool as described above in “Replacing the trimmer line and Spool”.

MAINTENANCE

Always remove the battery pack from your trimmer after use. 
Always check the product prior to being used for any damage.

After use, disconnect the battery from the tool and check for damage.
Your power tool requires no additional lubrication or maintenance. There are no user serviceable parts in 
your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. 
Always store your power tool in a dry room temperature location. Keep the motor ventilation slots clean. 
Keep all working controls free of dust.

Troubleshooting

The following table gives problems and actions that you can perform if your machine does not operate 
correctly.
Warning: Switch the machine off and remove the battery prior to any troubleshooting.

Summary of Contents for HT19-401-003-03





































Reviews: