PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL AND OPERATE
THIS LIGHT.
THIS PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN.
ALL ELECTRICAL EQUIPMENT AND APPLIANCES MUST BE CHECKED TO ENSURE THEY ARE SAFE
BEFORE OPERATING.
POWER SUPPLY LEADS, PLUGS AND ALL ELECTRICAL CONNECTIONS MUST BE REGULARLY
CHECKED TO ENSURE THEY ARE NOT LOOSE, WORN OR DAMAGED AND CIRCUITS ARE WELL
INSULATED.
WORN OR DAMAGED LEADS, PLUGS OR CONNECTIONS SHOULD NOT BE USED AND SHOULD
IMMEDIATELY BE REPLACED OR REPAIRED BY A QUALIFIED ELECTRICIAN.
THE RISK OF ELECTRIC SHOCK SHOULD BE MINIMIZED BY THE INSTALLATION OF APPROPRIATE
SAFETY DEVICES INCLUDING THE INCORPORATION OF AN RCCB (RESIDUAL CURRENT CIRCUIT
BREAKER) INTO THE MAIN DISTRIBUTION BOARD.
DO NOT WIRE THIS FLOODLIGHT INTO THE LIGHTING CIRCUIT. USE A SWITCHED FUSED SPUR (FIG.3).
CABLES SHOULD ALWAYS BE PROTECTED AGAINST SHORT CIRCUIT AND OVERLOAD.
ENSURE THE VOLTAGE MARKED ON THE PRODUCT IS THE SAME AS THE ELECTRICAL POWER SUPPLY
TO BE USED.
DO NOT PULL POWER CABLE ONCE INSTALLED AND DO NOT PULL POWER PLUGS FROM SOCKETS BY
THE POWER CABLE.
DO NOT INSTALL THE LIGHT:
- WHERE IT IS LIKELY TO BE KNOCKED OR HIT
- IN HOT OR HUMID CONDITIONS SUCH AS BATHROOMS, SHOWER ROOMS OR SAUNAS
- NEAR AN EXHAUST OUTLET E.G. BOILER FLUE, DRYER OUTLET
THE LIGHT BECOMES VERY HOT DURING USE. THEREFORE DO NOT TOUCH THE LIGHT WHEN
OPERATING, AND ALLOW TO COOL BEFORE TOUCHING.
THE LIGHT SHOULD NOT BE USED NEAR FLAMMABLE OR COMBUSTIBLE MATERIALS (SUCH AS
WOOD, CLOTH, PAPER) OR NEAR FLAMMABLE, COMBUSTIBLE OR EXPLOSIVE LIQUIDS, SOLIDS,
GASES OR EQUIPMENT.
DO NOT DIRECT THE LIGHT INTO A PERSONS EYES. THIS UNIT HAS A VERY INTENSIVE LIGHT OUTPUT,
WHICH IF INCORRECTLY USED COULD CAUSE EYE DAMAGE.
DO NOT USE THE LIGHT WITHOUT THE FRONT GLASS SHIELD. AVOID TOUCHING THE GLASS SHIELD
AS HANDLING MAY REDUCE ITS SERVICEABLE LIFE AND CAUSE THE GLASS TO CRACK.
THE MAINS POWER SUPPLY MUST BE DISCONNECTED BEFORE SERVICING OR PERFORMING ANY
MAINTENANCE.
THE LIGHT SHOULD BE MAINTAINED IN GOOD CONDITION WITH REPAIR ONLY BE UNDERTAKEN BY A
QUALIFIED ELECTRICIAN.
REPAIRS SHOULD ONLY BE CARRIED OUT USING GENUINE PARTS. NON-AUTHORIZED PARTS MAY BE
DANGEROUS AND WILL INVALIDATE THE WARRANTY.
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT INSTALLATION INSTRUCTIONS
IMPORTANT OPERATION AND MAINTENANCE INSTRUCTIONS
1 x
LED floodlight with PIR and mounting bracket
1 x
Fixing kit (4 x wall plugs, 4 x No.8 masonry screws)
1 x
Instruction manual (please keep safe for future reference)
• Electric / hand-held drill
• No.8 masonry drill bit
• Electricians screwdriver
• Large screwdriver
• Wire cutters
This product is suitable for wall mounting.
PARTS INCLUDED
TOOLS REQUIRED
TECHNICAL SPECIFICATION
230V AC - 50Hz
6W LED
8-10 Metres
@
15-20ºC
120º
15 secs - 5 mins
Day/Night or Night
Only opertation
IP44
6W
Power Supply
LED Light
Detection Range
Detection Angle
Time On Adjustment
Dusk Level Adjustment
Environment Protection
Power
HLL060
6W LED Floodlight
with PIR
230V AC - 50Hz
12W LED
8-10 Metres
@
15-20ºC
120º
15 secs - 5 mins
Day/Night or Night
Only opertation
IP44
12W
HLL120
12W LED Floodlight
with PIR
230V AC - 50Hz
12W LED
8-10 Metres
@
15-20ºC
120º
15 secs - 5 mins
Day/Night or Night Only
opertation
IP44
12W (on PIR detection)
6W (Dusk till Dawn)
HLL125
12W DUO Dusk till dawn
LED Floodlight with PIR
